Reloading Label tip

[RandyP]

I know they are available commercially but being frugal(OK I'm cheap-lol) - I created a template in Word that I use to make reloading labels using the Avery self-adhesive 8163 label. Built into Word is the ability to type one layout and then have it print a sheet full of many of different 'stock' label numbers available at any office supply place. The label size is 2" x 4".

Here is a pic of the label I use to show Date, caliber, powder used, charge, primer used, bullet make and weight/style. If I loaded many different powders I would put the disk# next to the weight of charge. Rather than keep a log book of any kind I just stick one of these labels on each box of ammo I reload.

 

[esheato]

I do the same thing.

I use Avery White Repositionable Shipping Labels (#58164) 3 1/3x4".

Every ammo can gets a label...and the fact that they're repositionable means I can remove them without leaving gunk all over the can to change them out when I change loads.

For regular load development, I just use a Sharpie on the MTM ammo box. A bit of rubbing alcohol removes any trace for the next load.

 

[rcmodel]

Good tip on the Avery labels.

Unfortunately, I am computer challenged enough that getting Word & my printer to cooperate that far probably isn't going to happen.

But I do use printed labels.
I set up a Word document years ago to print reloading box labels on plain paper.

I cut them out and tape them inside the box lids with Scotch Magic Tape.
I leave a doubled over "flap" of tape to get hold of.

That way, they are real easy to remove the next time I use the box again.

rc

 

[esheato]

RC,

Go to your favorite office store and buy the Avery White Repositionable Shipping Labels (#58164) 3 1/3x4".

Download the attached template, and open it in Word. Fill out labels to your liking. Feel free to use mine as an example. Insert the labels into your printer according to the directions. Hit print.

Easy.

 

[Walkalong]

I also do something similar with Avery labels. I print calibers/loads on them to put on ammo boxes. Your idea to make a load label with them is a good one. I believe I will give it a try. I like the way you did yours.

 

[mbopp]

As my brass supply increases I've been "recycling" cardboard ammo boxes from the range. I put a piece of packaging tape on top of the box, then use a 33-label template but print them on plain paper and Magic Tape them over the packaging tape.
I'll have to try rc's idea of doubling the end over for easier removal.

 

[W.E.G.]

I use RC's method.

I got tired of fighting those old labels off the ammo cans, and then scraping off the residue.

That, and the ones that the glue dries out, and the label just falls off.

The Scotch tape comes off easily, and only comes off when you want it off.

 

[kelbro]

Nice. Much neater than my masking tape and sharpie labels on the outside, folded over post-it on the inside.

 

[ArtP]

Midway sells generic white cardboard w/ Styrofoam insert boxes. They're the same size as factory boxes and cost a little less than 50 cents each if you buy quantity 25.

For long-term storage they work great and don't tie up my 100 round MTM boxes.

http://www.midwayusa.com/product/67...pringfield-20-round-cardboard-white-box-of-25

 

[esheato]

Got those too as they meet the airline regulations.

Straight from American Airlines:

Ammunition in its original packaging from the manufacturer is preferred, however it will be accepted in fiber, wood or metal boxes, or other packaging specifically designed to carry small amounts of ammunition. Loose ammunition or clips will not be accepted.

When I travel home to CA, I pack up the hunting rifle and some handloads in those styrofoam boxes and nobody gives me any attitude at the airport. I even cut a little rectangle out of my Pelican case foam to hold one box of ammo.

 

[cfullgraf]

Good idea to use the Avery labels.

I tend to be too lazy for that though. I use smallest blank Post-it notes with the basic information. Lot no., date, bullet, and powder charge. I use the Lot number so I can reference back to detailed info log.

 

[Twiki357]

I use the Avery Lables simular to RandyP, except I have them formatted in Excel.

 

[noylj]

I like the little Brother P-touch label printer. It is a thermal printer and templates can be made with the Brother P-touch Editor or any word processor that lets you set custom page sizes.
The label goes in the ammo box and then transferred to the target. I than take the target home and enter all the information, including the group sizes, into a spreadsheet program.
I used to write up a paper tag to go in the ammo box and then write the data on the target to take home. I prefer the label printer. One label printed at a time and no ink to ever buy. Can't do colors, but I don't need colors.

 

[capreppy]

I also use the Avery labels. They work really well, can print a fair amount of info, and DO come off when done. I've not been reloading long enough to have had any more than a few months, but I also don't load more than a few months worth of ammo (mostly because I don't have enough bullets to cover more than a few months worth).

 

[rondog]

I use Avery #6461 removable labels for mine. I had made up files for many calibers and loads, but when my hard drive crashed I lost all those. I haven't been able to figure out how to re-make them yet, it's frustrating. So I still use the labels, just write on 'em with a Sharpie now.

 

[Blue68f100]

I use a word template for Business Card stock. Most all of my pistol ammo is vacuum seal in food saver bags. With 9mm I put 200/bag, and 100/bag for 45acp. The only time I use plastic boxes is when working up loads or non-practice ammo.

 

[armarsh]

White electrical tape and a Sharpie. It's a beautiful thing.

 

[Bush Pilot]

White electrical tape and a Sharpie. It's a beautiful thing.

Is there a program for that?

 

[mahansm]

I guess I'm the computer weenie; I use MSAccess and do a label form, then print on Avery 33/sheet mailing labels. I've been doing that for a long time; I started with single column fanfold tractor feed labels through a dot matrix printer...

 

[BeerSleeper]

I used avery stick on labels, and the templates here. They work great, the only thing that would make it better would be if the pdf was fillable, so when doing volume production, I could fill it out with the printer.

 

[RandyP]

I should add that at 62 I guess I am somewhere between Luddite and PC guru. -LOL- but I am certain that my handwriting sucks - a chimp with a crayon would be neater -lol

So for me the labels are a simple, cheap way to keep a neat record without having to mess with spreadhseets or reloading logs. I try not to complicate my hobbies more than necessary.

 

[armarsh]

Is there a program for that?

Exactly!

White electrical tape and a sharpie: Re positionable, legible, waterproof, clean release, make it any size you want, $2.50 worth lasts years.

Best of all, no computer required.

 

[dickttx]

I like to use the 2x4 stick on labels. Each label is good for five loads. I just leave the old labels on, and see at a glance how many times a particular box has been loaded. I use plastic boxes for all my loaded rounds. I keep a couple of sheets in my Lyman handbook, so they are always handy.