Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Remington model 12-A .22

Discussion in 'Firearms Research' started by blechajo, Sep 30, 2003.

Thread Status:
Not open for further replies.
  1. blechajo

    blechajo Member

    Joined:
    Sep 29, 2003
    Messages:
    4
    Location:
    Albuquerque, New Mexico
    Mr. Nolden, perhaps you might be able and willing to help me. Romulus suggested you were the right person if there is one. I have just been given a Remington Model 12-A .22 cal. pump rifle. It was pretty cruddy. I broke it down, Not too difficult since it is made to be carried broken down in a nice small package. While cleaning it, the "action block" (that is my name for the piece that slides into the barrel assembly and is locked in by the trigger/stock assembly) dislodged itself, apparently because that is how you break it down. I can't get it back in correctly, hence the rifle either will not go back together, barrel/pump to trigger/stock or if I get it together, the block wedges incorrectly by tipping down in front (toward the barrel). I really wonder if I did something stupid and do not remember or if there is a trick. Remington is no help. Your help or comment would be very much appreciated as I now have a clean treasure of an old .22 that will fit beautifully into my backpack, if I can figure out how to get the three parts back together. Please and thank you.

    Blechajo (Peerpers)
     
  2. Jagermeister

    Jagermeister Moderator In Memoriam

    Joined:
    Dec 23, 2002
    Messages:
    371
    Location:
    Brunswick GA
    I apologize for the delay. Had some difficulty finding the information. I just happen to find it in the Rifleman from a long time ago. I have sent by separate email, the information that I have.

    JM
     
  3. Jagermeister

    Jagermeister Moderator In Memoriam

    Joined:
    Dec 23, 2002
    Messages:
    371
    Location:
    Brunswick GA
    I have tried on several occasions to email you the information, however, there must be a firewall or something on your address. It will not send to that address.

    If you have another email address, I will try and send it there.

    JM
     
  4. blechajo

    blechajo Member

    Joined:
    Sep 29, 2003
    Messages:
    4
    Location:
    Albuquerque, New Mexico
    Thank you folks who were able to respond to my request for help. You have rewarded my effort with your own and it solves the problem. Now, if I can just use enough of my work time to learn to work with this forum, I will be happy and a whole lot more functional. Of course, I'd rather be out in the desert shooting my newly restored rifle. Thank you again.

    Blechajo (Peepers)
     
  5. wvanek

    wvanek Member

    Joined:
    Jul 2, 2006
    Messages:
    1
    Model 12 A Remington 22 short/short/long rifle

    I am having the same problem that a previous member had trying to get the bolt assembly/firing pin properly back into my rifle after breaking it down. I am not sure if I have something missing or simply do not know how to install the part. Or if something is broke.

    Also where is the Model number on this gun or the serial number. On the under side of the barrel is R.W.888; is that the serial number?

    Thanks in advance.
     
  6. bartman

    bartman Member

    Joined:
    Jan 3, 2003
    Messages:
    24
    Location:
    Palatka, FL
    turn the receiver/barrel upside down. see the slot milled into the inside of the top of the receiver? with the slide forward drop the properly oriented bolt into the rear of the slot. now cycle the slide rearward until it stops. see the little button directly behind the forearm wood? press it in and it will allow the slide to move back another 1/8" or so. now push the bolt forward with your finger.

    to disassemble, with the action upside down, cycle the slide rearward, push the little button to get the last bit of travel. when you cycle the slide forward the bolt should remain in the slot in the receiver. you might need to give it a jiggle to get the bolt to disengage

    the weapon has no model # on it. mine has the 'rw' but my sn is in the 251,000 range. remington's website has date of manufacture info if you're interested
     
  7. micah_johnson_92

    micah_johnson_92 Member

    Joined:
    Jul 27, 2008
    Messages:
    4
    I disassembled mine and I can't figure out where the "retainer" goes. Can anyone help me?
     
  8. Steven Mace

    Steven Mace Member

    Joined:
    Dec 24, 2002
    Messages:
    206
    Location:
    Peoria, AZ USA
  9. micah_johnson_92

    micah_johnson_92 Member

    Joined:
    Jul 27, 2008
    Messages:
    4
    That did help, but I am still having trouble. Do you have any other advice.
     
  10. micah_johnson_92

    micah_johnson_92 Member

    Joined:
    Jul 27, 2008
    Messages:
    4
    Disregard my last message. I've got it back together. Thank you for your help.
     
  11. OldArmy

    OldArmy Member

    Joined:
    Jul 29, 2008
    Messages:
    2
    Location:
    OKLAHOMA
    having the same problem with my modle 12 can you help JagerMeister?
     
  12. OldArmy

    OldArmy Member

    Joined:
    Jul 29, 2008
    Messages:
    2
    Location:
    OKLAHOMA
    Here is the site for anyone who has the same issue with the Remington model 12.http://www.wisnersinc.com/additional_info/remington_m12.htm Thanks goes to Micah johnson 92. Got to spend the last day of leave with my son teaching him how to shoot it. third generation to learn how to shoot with it.
     
Thread Status:
Not open for further replies.

Share This Page