Who's doing some loading tonight?

[klcmschlesinger]

Loaded up some 40's tonight. 180 grain xtremes with 700X. Also received 1000 more 9mm from xtreme. Should keep me busy for the next week or so depending on how much time I get.

So like I say in the opening? Who's loading tonight and what are you loading?

 

[jwrowland77]

Not really loading. Case prep and getting range bag ready to do some unloading tomorrow.

 

[rchery59]

Was loading .380 before and I'm about to go back to it in a minute. Another 250 or so and I"m officially out of bullets. Time to reorder, I've got lots of brass, primers and powder. Just no more bullets.

 

[fallout mike]

I loaded some .327mag just a bit ago.

 

[up 2 snuff]

Preparing 30-06 brass. Getting ready to work up new rounds for a couple rifles. I love cleaning primer pockets! It is relaxing.

 

[horsemen61]

Ooooooh mike what do you have in 327 mag and no I haven't loaded today

 

[cfullgraf]

Resized and prepped the cases that I unloaded this afternoon. 9x19, 38 Special and 357 Magnum.

I will load them at a later time when I am about out.

 

[ch84]

Loaded up 25 .357 mag rounds with 125 gr jsp with unique an 25 140 gr xtp's with 296. Shoot some of these the other day with good results eliminated different charge weights an 2400 powder.

 

[Rodahayes51]

Had a partial box of sierra 125 gr. spitzer soft point bullets that I loaded in to 7.62 x 39. Just trying to clean up leftovers!

 

[Rodahayes51]

I had a partial box of Sierra 125 gr spitzer sp that was calling me to get loaded. Made 33 7.62 x 39 rounds. Now I need to buy more to finish filling out my box!

 

[Dream of long range]

Seems like all the hardship trying to find powder and primers has left some of use short on bullets lol. Earlier I finished getting the papers ready to send for the hornady free bullet promo(kinda a pain in the rear).Gonna be waiting for those to work a load for a 30-06.

 

[mc2212]

Loaded 350 rounds of .40 earlier today and finished off the last of my Red Dot....dang

 

[jeeptim]

Colt .45 tryin to burn up about 1/4lb bullseye 350 cases and 200gr swc. Be lucky to get through 50 Stupid job.

 

[Schwing]

I just finished about 300 .44s a couple of hours ago. They are hand cast 240 grain SWCs that I powder coated black and loaded with 15 grains of blue dot.

 

[Storm_Shadow]

Just made some .308 with Varget and 168 Sierra OTM and going to start on some .44 mag with h110 and 240 swc.

 

[hartcreek]

I just powder coated and loaded 300 9mm with my Lee 105 grain and 4.4 grains of green dot.

 

[tightgroup tiger]

I'm doing a load work up for 41mag and power pistol. For now it's 12 at a time in different powder weights until I get to where I want to be on it. Then the fine tuning starts.

I also have 500 .327 fed mags to load and don't have time to load them on a single stage. My shell plate for my LNL-AP .32 H&R proved to be defective so I had to send it back to Hornady for replacement. The bottom ring that the spring rides against is way out of place and won't allow the spring to go down into groove in the sub assy. So I'm stranded on those for a while.

 

[Dave Dembinski]

Loaded up 10 rounds a piece of all the disks on my AutoDisk between start and max for v-N32C in 38 special (only 40 rounds, didn't take long). Going to chrono those as soon as I can and decide which one I want to crank out.

 

[Vodoun da Vinci]

Full length resizing and belling the mouths of the very first 300 .380 autos I have ever done last evening.....soaking and cleaning them right now and I'll prime 'em and charge 'em Sunday so when the new bullets show up Monday they are ready to *RoCk!* for next weekends further testing of Mama's new Glock 42.

Gaad, I *do* love the whole trip....load 'em, shoot 'em, tweak it (shooting technique and the loads) and repeat as needed until perfection or satisfaction.

Sounds like I ain't the only one either judging by how many others are working the presses as we speak.

VooDoo

 

[lauderdale]

Waiting on 1000 rnds. 380 nickel,1000 40S&W from once fired. Will be tweeking G42 380 90grn. xtp"s. /cleaning up about 700 rnds. 380!! Fun Fun Fun!

 

[Conservidave]

I've got lots of brass, primers and powder. Just no more bullets.

Thats all i got

 

[Tony k]

sized and cleaned the pockets on 90 .223 rem cases. Probably gonna use them for continued work up with my 65 grain sierra game kings. 24.8 grains of h335 yielded a .73" group (5-shots) out of my 16" bushmaster. Unusually me and this gun are only good for about 1.25-1.5" groups at best. I'm either on to a good combo or I got lucky.

 

[wlkjr]

Rainy here so I'd headed to the shop to load the rest of the .380 bullets I have left for the new G42. After that I'm loading up some 124 Xtremes for my wife's new Gen4 19.

 

[UKWildcatFan]

Trimming 500 pieces of .223. Wheeeeeeeeeeeeeeeeeeeeeeeeee!!! I'm just glad I have enough powder to load my 6,000 projectiles. Yes, I'm on a Dillon 550. Thank goodness.

 

[jim243]

Just loaded a new load of 75 grain Hornady's for a new bolt rifle in 223, will go into production as soon as I can see how they shoot.

Jim