Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Writer has handgun serial number question.

Discussion in 'Handguns: General Discussion' started by jpod, Aug 16, 2011.

Thread Status:
Not open for further replies.
  1. jpod

    jpod Member

    Joined:
    Aug 16, 2011
    Messages:
    6
    Good Evening. I am jpod and I am a mystery/thriller author. I need some assistance with a technical point for my current novel. Is there a handgun that has the serial number located in more than one place? So, if a perpetrator obliterates the serial number of a stolen gun, the serial number may be present in another area (e.g. under the grip, etc) that would allow the police to prove that he is the person who stole it? I would need to know the make and model of this gun. Thank you.
     
  2. Mxracer239y

    Mxracer239y Member

    Joined:
    Nov 5, 2008
    Messages:
    108
    Not that I know of, but serial numbers are most often stamped. Even if the actual stamping is ground off there is affected metal beneath, of higher density than the rest of the frame. Using electrical/chemical methods one can sometimes 'read' the serial number from the affected material below.
     
  3. Old Fuff

    Old Fuff Member

    Joined:
    Dec 24, 2002
    Messages:
    23,908
    Location:
    Arizona
    In what time period does your story take place? It used to be a common practice to stamp the serial number on various parts to insure that in final assembly the right parts got back into the correct frame or receiver.

    Also Smith & Wesson used to stamp the serial number on the butt, but when stocks became popular that covered the butt they moved the number to the frame behind the yoke cut-out (the "yoke" is the hinge part the cylinder swings out on). During other times on the inside of the sideplate, back of the cylinder, bottom of the barrel, under the extractor star, inside of each grip panel - and of course the butt... :uhoh:

    I could go on and on...
     
  4. Trebor

    Trebor Member

    Joined:
    Feb 15, 2003
    Messages:
    4,817
    In many cases removed or defaced serial numbers can be recovered by a police lab. It's a fairly common technology that has been around for decades.

    In the U.S. the "official" serial number is the number on the frame. The manufacturer may have marked a serial number in another place, like the barrel for instance, but those serial numbers have no legal standing. The only "valid" number that is used for any sort of legal purpose is the serial number on the frame.

    And, yes, there have been many handguns made over the years with the serial numbers marked in more then one location.

    Here's an easy example for you. Many S&W revolvers have the serial number stamped on the bottom of the butt of the gun. With the original wood factory grips the serial number is visible. However, if someone replaces the grips with an older set of oversize Houge rubber grips the grips will cover the serial number. (Newer Houge grips are made to allow the serial number to still be seen).

    If someone is not familiar with that revolver the only thing that "looks like" the serial number are the numbers etched in the crane of the revolver that are visible when you open the cylinder. The thing is, those are usually a part number used to keep all the parts of that revolver together during assembly and is not the same as the serial number and is not actually the serial number.

    Essentially, someone has a pistol, the rubber grips cover the real serial number, the bad guy doesn't know this so he "erases" what he *thinks* is the serial number in the crane. The police recover the gun, notice the crude attempt to erase the serial number on the crane, but simply remove the grips to reveal the real serial number hidden under the grip the bad guy didn't even know about.

    I have a Smith & Wesson Model 15 .38 Special revolver where the real serial number is not visible under the rubber Houge grips that has a different "assembly number" on the crane that could be mistaken for a serial number by someone who doesn't know better. (That's a six shot .38 Special revolver with a 4" barrel, adjustable sights, and blued finish, btw).
     
  5. 56hawk

    56hawk Member

    Joined:
    Mar 29, 2011
    Messages:
    1,298
    Here are pictures of a Smith & Wesson for you.
     

    Attached Files:

  6. armoredman

    armoredman Member

    Joined:
    Nov 19, 2003
    Messages:
    16,213
    Location:
    proud to be in AZ
    My CZ P-01 has the serial on the barrel visible through the ejection port, and down near the muzzle on the slide, but both are quite visible. I agree on the Smith serial and assembly number confusion - when I got my Smith 10-8 approved as an alternative off duty gun, the armorer told me that I had the wrong serial number on my paperwork. When I showed him the correct one, he insisted on writing both of them down on my form, to my vast amusement. I have Pachmeyer presentation grips that cover the bottom of the butt and the true serial number thereon.
     
  7. Zak Smith

    Zak Smith Moderator Emeritus

    Joined:
    Dec 24, 2002
    Messages:
    9,037
    Location:
    Fort Collins, CO, USA.
    Glocks have the serial number on the three principal components: frame (the "legal" serial number), slide, and barrel.
     
  8. Bobson

    Bobson Member

    Joined:
    Aug 9, 2011
    Messages:
    4,140
    Location:
    Snohomish County, Washington
    Doesn't Springfield do the same thing for the XDm?
     
  9. SigP229R

    SigP229R Member

    Joined:
    Sep 6, 2008
    Messages:
    385
    Location:
    North Carolina
    At one time Sigs had their serial Nos. in three places; barrel, slide, and frame. My P6 is that way but, I think they are getting away from that now.
     
  10. Trebor

    Trebor Member

    Joined:
    Feb 15, 2003
    Messages:
    4,817
    I just thought I'd mention again that before you take this plot point too far how relatively easy it is for the police to recover a defaced or "filed off" serial number. The procedure for doing so has been around for decades and newer high tech ways of doing it have made it even easier.

    Just a thought before you hang too much on the idea that the "bad guy would have got away with it because he removed the serial number but didn't know about the second serial number" idea.
     
  11. GCBurner

    GCBurner Member

    Joined:
    Nov 18, 2010
    Messages:
    1,853
    I believe that under current Federal law, just posessing a gun with an obliterated serial number is a Federal felony, whether the posessor is the one that originally stole it, or not. Mere posession of a stolen gun does not prove that the posessor is the one who stole it, and there is no way that I know of to prove who stole or used a gun by the serial number alone. That's why stolen guns that are used in crimes are usually destroyed, thrown away, or sold to other criminals as fast as the shooter can get rid of it after the crime is comitted. Nobody with any sense would use a gun with a paper trail from a legal purchase in their own name to comit a crime.
     
  12. Yukonstorm

    Yukonstorm Member

    Joined:
    Feb 19, 2006
    Messages:
    51
  13. birdshot8's

    birdshot8's Member

    Joined:
    Jan 20, 2008
    Messages:
    542
    Location:
    north platte, ne
    S&W Perfected circa 1915

    My Perfected in 38S&W has the serial number in 3 locations. under grip, face of cylinder and on rear sight. as posted above i believe this was to facilitate assembly.
     
  14. jmr40

    jmr40 Member

    Joined:
    May 26, 2007
    Messages:
    9,887
    Most European made guns will have the SN on frame, slide and barrel. USA made guns are usually frame only. Some (maybe all) S&W revolvers have the SN on the butt as well as inside the frame. The one on the butt cannot be seen with most grips installed.

    All my bolt action rifles have the last few digits of the SN on the bolt. This is to ensure the correct bolt goes out the door with the correct rifle since the bolt is not always with the gun during production.
     
  15. Tallinar

    Tallinar Member

    Joined:
    Jun 4, 2010
    Messages:
    604
    Location:
    Des Moines, IA
    I'd be interested to see what kind of fictional point you'll cook up with this topic.

    The receiver stamp is the one that ID's the gun, really. The other parts could just as easily have come off another gun at some point in time and won't necessarily match.

    I've owned several old service rifles with unmatching serial numbers on the bolt and receiver. If I scratched off the serial number of the receiver, one would be incorrect to try to use the bolt serial number as a means to ID the gun. It is very common to find guns (especially like old service rifles) which have had serial numbered parts changed out during their lifespan for one reason or another (part breakage, undesireable headspacing, etc).
     
  16. wideym

    wideym Member

    Joined:
    May 30, 2007
    Messages:
    928
    Location:
    Arkansas
    Some older guns have no serial number at all, as it was not required, but are still in circulation. Also filing or scratching off a serial number might be ineffective, but while I was in the Army, CID recovered an M16A2 that they were sure was US property. The problem was that the entire portion of the magwell that had the info was cut out with a drill press. The guy still went to jail for possesing an unregister MG, but they could'nt prove it was a military weapon.
     
  17. tbutera2112

    tbutera2112 Member

    Joined:
    May 14, 2011
    Messages:
    161
    my HK also has it in a few places

    frame
    barrel
    slide

    but all places are highly visible....the barrel and slide you really cant miss, and if you flip the gun upside down you can see it on the frame, its even on a stainless plate with black lettering, so it really pops out

    if someone was removing serial numbers, they couldnt miss any of the 3





    also note - a lot of states dont have registration - so there may not even be a point to take the number off....here in ohio, no registration...so any gun ive bought here, if stolen and used in a crime, would never trace back to me because they arent registered to me....private sale or ffl
     
  18. jpod

    jpod Member

    Joined:
    Aug 16, 2011
    Messages:
    6
    Thank you all for your informative replies. It is a contemporary story. Basically, the private eye (the protagonist in my novels) disarms an intruder who tries to kill him. The intruder escapes, but the private eye retains the gun and notices that the serial number on the barrel has been obliterated. However, when he removes the grip, he finds the serial number that was stamped on the frame. This serial number allows him to trace the handgun to its original owner (not the intruder)--- a key aspect of the plot.
    Hope this explains why I needed this information. Any and all comments are welcome. I appreciate your help.
    JPOD
     
  19. k-frame

    k-frame Member

    Joined:
    Jan 22, 2007
    Messages:
    260
    Location:
    Outside of Atlanta
    jpod, how do you plan to link the serial number to the original owner? Do you plan to have the protagonist contact the manufacturer? Or was the weapon reported stolen and the owner gave the SN to the police?

    The members here (excluding me :) ) may have some more advice for you in this area.

    ETA: Check out this thread: http://www.thehighroad.org/showthread.php?t=609383 for a discussion on serial numbers and gun non-registration. It may give you some more ideas.
     
    Last edited: Aug 18, 2011
  20. Trebor

    Trebor Member

    Joined:
    Feb 15, 2003
    Messages:
    4,817
    How is he able to trace the handgun to the original owner?

    In real life, the ATF can trace a firearm from the manufacturer to the distributer and then to the retail outlet and the first retail purchaser. It's an involved process though as most of the paperwork is not electronic and paper records have to be hand searched. This is especially true of older paperwork.

    (And each step has to be done. The manufacturer would have no idea where it went after it went to the distributer, and then the distributer's records have to be searched to find the retailer, and then the retailer's records have to be searched to find the buyer).

    Local law enforcement agencies can request the ATF do this, but normally would have no reason to do so. If the ATF did do this at the request of a local agency it would take a couple months, minimum, for trace to work through the process.

    There is no way for a PI to have access to this kind of trace. There is no centralized database he could access, or even hack into, to get the info. And, it's not as simple as "asking for a favor" from a police friend or even a ATF agent. The whole trace process is cumbersome and requires official paperwork and effort on the part of many people.

    I do have a workable alternative for you though. For quite a well it was popular for firearms owners to electro pencil their name or other ID on their guns for proof of ownership in case of theft. Because this was kind of ugly, it would often be done under the grips.

    In some cases people would add their Social Security number as well (this was before worries of identity theft).

    The PI could disarm the bad guy and, when he checks under the grips, find the original owners name and possibly even soc sec or old phone number or driver's license number. (I've seen all three used as ID on guns before).

    Of course, this only works if the bad guy stole or "borrowed" the gun from the original owner. If the original owner gave the bad guy the gun specifically to kill the PI, then the original owner obviously wouldn't give the bad guy a gun to use that had the owner's name electopenciled on the gun.

    This avoids the whole "impossible for the PI to trace the gun" problem.

    EDIT: I forgot to include the possibility of a state level registration system that the PI could get access to, probably unofficially. If the state the story takes place has handgun registration, that is a possibility, and would be more likely then a ATF trace.
     
  21. gyvel

    gyvel Member

    Joined:
    Sep 18, 2009
    Messages:
    577
    Location:
    Northern AZ
    If I recall correctly, some Spanish Star and Astra pistols have the serial number stamped in a visible place on the frame and again under the grip. Also, some FN/Browning guns like the 1910 and 1922 .32 and .380 have the complete serial number stamped internally on the underside of the slide

    At any rate, to thoroughly obliterate a serial number on metal, you have to give it a real "workout' with a metal center punch to completely alter the molecular structure of the metal where the original number was stamped.

    The most common method for years was the application of acid to the area where the serial was. The stamping of a character "upsets" a certain amount of metal around said character, i.e. compresses it, making the molecular structure more dense. When the acid is applied, the oxidation rate is different for the compressed metal and a faint outline of the character becomes visible.

    Having said that, there are modern high tech methods in use now that have more or less made the acid method obsolete. However, I still think a good working over with a steel center punch will sufficiently alter the metal enough to obliterate the original characters completely.
     
  22. gyvel

    gyvel Member

    Joined:
    Sep 18, 2009
    Messages:
    577
    Location:
    Northern AZ
    A bit of a technical point here: Removing the serial number on a barrel would (a) not be a violation of Federal law and (b) only prove that the barrel was stolen.
     
  23. larryh1108

    larryh1108 Member

    Joined:
    Aug 29, 2008
    Messages:
    2,326
    Location:
    NC
    I think we are thinking too deeply. For most people not familiar with guns and gun laws a fiction writer can easily make up a ficticious database, etc. Remember, it's a made up story in the first place. With the way computers are now today, it's not a stretch on making up anything and have it be believable.
     
  24. bigbomar4

    bigbomar4 Member

    Joined:
    Jun 16, 2011
    Messages:
    52
    Location:
    Lubbock, TX
    If the gun was stolen and reported stolen would the sn not be in the NCIC database along with the person who reported it stolen? To add to this what about poly guns? The only sn I see on my ruger is on the poly frame. That could go away very easily.
     
  25. 19&41

    19&41 Member

    Joined:
    Jun 17, 2010
    Messages:
    291
    Location:
    Georgia
    What about the recent developments involving Chiappa and the attachment of an RFID chip to the polymer portion of their Rhino pistols?
     
Thread Status:
Not open for further replies.

Share This Page