Thank You 243winxb for the info. on the web sight. It should get me close enough to a starting load.
I want to use the 260 WFN bullet in my S&W 29-3 Classic Hunter
I want to shoot on paper @ 100yds.
I need to keep FPM under 1000.
Thank You all for your input. Hank
Need Help. I have bought LEAD bullets from Montana Bullet Works for my S&W 29-3 Classic Hunter W/6" Barrel
The mold used was a LBT 260gr. WFN and 250gr. LFN.
I have about 12lbs. of 700X powder that I would like to use if possible.
I want to try the two different bullet styles to see which...
What is the difference between boiled linseed oil and tung oil to refresh a M1a rifle stock. I don't want to change the density of the stock. It has some nice grain I would like to bring out. The stock looks starved and dry. I just want to refresh the stock as per the owners manual. By the way...
700 X is a good light target load for .44 Special reloads. Buying brass should not be a problem. You will have to do extra cleaning on in the cylinders. Good luck and have fun.
I've used oil on my carry ammo for the last 35 years. I lightly oil a rag and coat the brass only. I have kept this ammo in my revolver for over a year and then fired all 6 cylinders with no problems. I then clean my Model 19 and hope I never have to use it. To make a long story short. BE...
Has anyone replaced the action spring with a Wolff extra power recoil spring on a Remington 1100? If so, can you feel the difference. Will it hurt the shotgun shooting trap & skeet loads only. Thanks, Hank
Hey Guys, Can you tell me if a Colt Gold Cup Series 70 is set up to shoot 180-200Gr LSWC bullets without doing work on the Match Barrel and feed ramp? Thanks, Hank
Thanks Old Fuff. You are correct about double firing. After shooting about 1500 or so rounds my Colt went full auto. The gunsmith did something to solve the problem. It has never happened again. When I reinstalled the Depressor and Depressor Spring my Colt functioned great. After shooting about...
I have a Colt Gold Cup Series 70 I purchased in the 70's. It is a tack driver. I decided to completely strip it to check for wear. To my eye everything looks fine to me. A gunsmith I shot with at the time removed the Depressor and Depressor Spring. He said the parts do not hold up. About a year...
Is there a way of removing the bolt from a Springfield M1A Super Match without field stripping the rifle. This rifle is glass bedded and I don't want to take apart. Hank
Can you tell me which rifle will shoot more accurate, all things being equal. A rebuilt M1 Garand with a new barrel .30-06 or a Springfield M1a .308. I am only interested in these rifles only. I will hand load for both rifles.
Thanking you in advance, Hank
I purchased a Lyman casting kit back in the 70's. It sat in the garage until this month. I never had the need to cast. Lead was cheap. However the cost of lead has increased to the point I want to start casting. When I purchased the kit I bought Lyman molds for .38/357 and .45ACP. I want to...
Hey Guy's, I am looking for a target load for the .38 Special with cast 148gr. wadcutters. I will be shooting indoors. I would like the powder to be clean burning with low smoke if posible. Thanks,Hank
Thanks Guys, I will try it on some .45 brass before cleaning my .30-06 brass.
"JUST A NOTE" on the Thumlers Tumbler. I have been using the tumbler since the 70's. You can get some fine polish from Thumlers that will make your brass look great. I still have the same tumbler, had to replace the...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.