Search results for query: *

  • Users: cvo
  • Content: Threads
  • Order by date
  1. C

    Varget vs Tac

    I have a 18" JP upper I am going to try some 77 SMK through. I have both powders, whats your thoughts on the two powders with the 18" barrel. SMK's are cannelure. BTW, I am not worried about the metering of Varget, and I know TAC is more temperature sensitive.
  2. C

    Trimming .556 brass

    Besides using a Dillion trimmer, what is the other options?
  3. C

    Dillion 550 powder bar question

    What is the max grains out of the small bar?
  4. C

    MG 124 FMJ with 231

    Anyone using this combination? I would like your input on your load and COL using MG 124 FMJ with 231 powder.
  5. C

    For all the "I save by reloading"

    You don't save by reloading, but you can lower your cost at some point. If you to want "Save" put your money in a CD!
  6. C

    Dillion 550B Shell Plate Question

    I have been loading .45 for about One year now. Yesterday I noticed that one of the Brass pins on the shell plate holder has a larger diameter head. Why would it be larger, and I don't remember anything in the setup that states one is larger. Do different calibers require different size pins...
  7. C

    Loading .380 Short Barrel Speer Gold Dots

    I have the data on the Speer 3992 bullet, but I can't find any data on the 4020 short barrel bullet. Anyone know the difference in the Two bullets?
  8. C

    FMJ vs CMJ

    If you had your choice at the same price which one would you choose? Is their a performance difference between the Two? I am looking at the MG 124's 9mm.
  9. C

    People Say W231 and HP38 are the same

    Page 532 in the Modern Reloading Second edition calls for 4.7gr of HP38, 4.3 gr of W321. Start load for 115 9mm jacketed bullet. Is the book wrong?
  10. C

    Downside To Lead Bullets

    I would like to try loading some lead 230 gr RN for my SA. So my question is what is the downside, besides barrel leading?
  11. C

    9MM 124 FMJ RN Armscor bullets ?

    Whats the consenses on these, are they OK for plinking? I found some for $86 per K shipped. ISO certified made in the Philippines.
  12. C

    Plated .45 Load

    I can't find any info for plated powder loads. Should I assume its the same load as a Lead round nose? BTW, I am using RMR plated RN 230 grain bullets with W231.
  13. C

    Crimping Plated Bullets

    I had been running Hornady .230 FMJ in the Dillon and switched over to .230 plated bullets. First thing I did was take one apart and I noticed the crimp cut into the plating pretty bad, I take it this isn't good? The case is 0.471 at the mouth. Should I back off on the Crimp, or will it...
  14. C

    +P Loads

    Exactly why do they call it a Plus P? If you use a +P case does that make it a + P load?
  15. C

    Tell Me Whats Wrong

    I've been reloading rifle for a long time, but this is my first attempt at pistol. This is once fired Federal .45 brass with a Hornady 230 grain XTP bullet. I can see the expansion from the bullet in the case, is this normal?
  16. C

    Need A New Setup

    I've been doing 308 bench rest loading for few years now on a single stage. But I have recently purchase a M16 and need a faster press than my single stage, my only interest is loading for this gun. Thanks
Back
Top