Search results for query: *

Being smarter than the equipment that I'm operating- I don't remove safety/transfer bars from my FA revolvers. The IDIOT that did,got what he deserved-right between the eyes. One aspect is certain, the IDIOT will not be reproducing making more like him. Family attempting to cover kin's screw...

I haven't had any Ruger pistol issues in 30+ years. Since that was the last investment cast Ruger JUNK that I have touched. Purchase a Freedom Arms 83's &/or 97's & you'll give the Ruger schit away!!

Check scope base screws & action screws for proper length as they may be binding the bolt. Remove,disassemble,clean,adjust the trigger group completely or seek a professional to accomplish the task.

Rent the reamer,tap & bushings from 4D Reamer Rentals in MT for $60 to accomplish the task yourself in 1/2 an hour.

By rotating the take down lever,you are able to slide 4 top end assemblies of .22LR,9x19,357Sig,40S&W on that SIG P226 frame. All my P220's,P226's,P227,P228,M11-A1,P229's have multi caliber/top end options.

Install or have installed by a competent 'smith a Trigger Tech trigger group & eliminate the OEM Rem X Mark-MIM'd JUNK.

SIG SAUER P229 for double stack mags or SIG SAUER P239 for single stack mags. Purchase a SIG SAUER 357SIG Bbl for either of your choosing(s). Anything TUPPERWARE should stay in the cupboard where it belongs!

2 stage options to pin into a 700/40X action- BixNAndy Competition or Tac Sport Flavio Flare CG Jackson Geiselle Super 700 Anschutz w/ adapter or machine work Tubb T7T Single stage options- BixNAndy Tac Sport Jewell Trigger Tech Geiselle 700 Rem 2oz Rem Int'l 2oz Rem 40X Repeater I personally...

jski, 35 Rockwell "C" scale is not hard. As previously posted- grease is definitely needed/required. Give it time,it will work harden & crack.

OP, Has this X Mark trigger group recall been complied with by Remington. Have a qualified gunsmith,not a DIY gun plumber, disassemble,clean,adjust,seal,re-install the trigger group. Or we'll have someone else standing in line to sue Remington for proclaimed accidental discharges by shooting...

Yes,IF your LC head stamp date(90's) is prior to ATK's involvement.

You purchased a 700 LH (left hand) DM (detachable magazine) rifle of which has the black fore end tip found on BDL rifles. This action DOES NOT have feed rails to feed from an internal magazine box(ADL/BDL) so it will ALWAYS require a magazine to function by design.

First- Move out of NY,or any Blue state that voted for Hitlary Clinton that will impose restrictions on your rights/dreams. Gunsmithing is a labor of love.

Purchase an ArmaLite & don't look back! Steel magazines work & have worked well since their adaptation in the M14/M1A.

Typical case hardened Win part. The lever has a burr locking it in the fire position. Dis-assemble,blend & re-assemble.

Remove firing pin from bolt. Take measurements of existing length. TIG weld a drop of 4130 CrMo to the firing pin TIP. Work harden Blend Re-install firing pin DONE 10 minute job NO Rocket Science involved!

Compare the magazine systems- ArmaLite AR-10 Original/modified M14,"STEEL MAGAZINES"-Gen1 Re-tooled to eliminate contract M14 junk w/"STEEL MAGAZINES"-GenII There is a reason our fed gov't doesn't contract "PLASTIC" links/belts for machine guns!! If your mouse/rat gun accepts plastic...

BATF regs state- Silver Brazed(1400deg F) not soft soldered(450-600deg F) devise to Bbl or by welding. As stated previously once installed-,drilled,pinned & TIG welded/blended-Permanent by Fed Regulations!

Remington Nickled brass,Fed 150 LP primer & 12.0gr of AA#7 behind a Speer 180gr Gold Dot HP seated to 1.250OAL. Will run @1300fps out of a 5" S&W slide gun. Combat Tupperware (Glocks)will malfunction with the above load.

In supported chamber slide guns- 12.0gr of AA#7 behind a jacketed 180gr chrono's @ 1300fps from a 5" slide gun. The combat tupperware's un-supported chamber renders the brass junk & induces enough harmonics into the frame that they won't pick up the next round.