Search results for query: *

Hope I posted in correct forum: To get my Winchester Model 74 (semi-auto) .22LR shooting reliably, I had to gently hammer/straighten a bent guide pin in the bolt. I took it down to the range to see how it shoots. It has iron sights, and it is shooting an inch to the right at 25 yards. Is this...

Hi! I have purchased a Springfield XDs 9mm 4" barrel pistol. I am finding several good loads that I worked up for my Sig M11-A1 (P229) 9mm 4" pistol that will not plunk in my XDs. Evidently the XDs needs a shorter COL for some of the bullets I have on hand. I have found the working COL for...

Hi1 Looking for some guidance in using or not using Titegroup powder for my applications. I have some Titegroup I am planning on using in 9mm. The gun to be used is a Sig M11-A1 9mm, 4" barrel, standard recoil spring. The bullets I have available are 124gr/125gr plated and jacketed and 147gr...

38SPL Roll VS Taper Crimp CAUTION: The following thread includes posts of loading data tested in my guns chambered for this cartridge. USE AT YOUR OWN RISK. Neither the writer, The High Road, nor the staff of THR assume any liability for any damage or injury resulting from use of this...

38SPL Range Report CAUTION: The following thread includes posts of loading data tested in my guns chambered for this cartridge. USE AT YOUR OWN RISK. Neither the writer, The High Road, nor the staff of THR assume any liability for any damage or injury resulting from use of this information...

PAGE 1 CAUTION: The following thread includes posts of loading data tested in my guns chambered for this cartridge. USE AT YOUR OWN RISK. Neither the writer, The High Road, nor the staff of THR assume any liability for any damage or injury resulting from use of this information. This being...

PAGE 1 CAUTION: The following thread includes posts of loading data tested in my guns chambered for this cartridge. USE AT YOUR OWN RISK. Neither the writer, The High Road, nor the staff of THR assume any liability for any damage or injury resulting from use of this information. This...

CAUTION USE AT YOUR OWN RISK: The following posts of loading data were tested in my gun chambered for this cartridge. Neither the writer, The High Road, nor the staff of THR assumes any liability for any damage or injury resulting from use of this information. Dudedog! Thanks for 147gr RMR...

USPS RATES scheduled for increase (includes Flat Rate Envalopes/Boxes) effective 1/17/2016: http://www.fp-usa.com/ratechange/january-17-2016-rate-increase/ Priority Mail Retail Pricing Flat Rate Envelope Legal Padded Small Box Medium Large Before...

I am contemplating upgrading my Sig P229 with a Bar-Sto Semi-Drop-In Barrel Sig Sauer P229 9mm Luger 1 in 16" Twist 3.8" Stainless Steel. Looking forward to opinions, pro or con, from members with hands on experience with Bar-Sto barrels. Thank you, JD

Hi all! I recently recieved in trade 1500 Plated Frontier 125 grain 357 bullets. I measured 50 bullets, they measured .3565" to .357" diameter. I would like to know if I can use these in my Sig 9mm pistol? Looking for advice from those that have tried this. Googled this question, found...

Hi all! Looking at upgrading from single stage to a turret press. Choices I am looking at are (in alphabetical order): Lee Classic 4 Hole Turret Press Lyman T-Mag 2 Turret Press RCBS Turret Press Redding T6 or T7 Turret Press OTHER SUGGESTIONS? I would like your pros and cons of these...

CAUTION: The following thread includes posts of loading data tested in my guns chambered for this cartridge. Posts by other THR members contain loading data tested in their guns chambered for this cartridge. USE AT YOUR OWN RISK. Neither the writer, The High Road, nor the staff of THR assume...

HA:D Made you look:what: MERRY CHRISTMAS AND HAPPY NEW YEAR:neener: (idea plagiarized from S&W FORUM:eek:) jell-dog

I'm looking for information on where I can find/obtain the article written by IIRR Jim E Clark Sr "Handloading for Accuracy in the S&W M52" printed in Gun Digest and also The Best of Gun Digest. I am not sure what year this article was written. Thank you in advance for any information you can...

Does anyone have any information on this die set? Has any one used this die set? Thanks for any and all replies!

I am not claiming that brass manufacturers produce “regular .38spl brass” and “wadcutter .38spl brass”. I am not a mechanical engineer or rocket scientist :what:, I am just presenting my basement best efforts and observations to determine if some .38spl brass is better suited to lead HBWC’s...

We all have heard the horror stories about some LGS's, how about bragging up your favorite LGS? I purchased a gun safe from MY favorite LGS, had problems finding a reasonable rate to get it delivered. Mentioned to LGS owner it would be a few days till I could get someone to deliver it to my...

New to the Model 52 platform, so here goes: My LGS has a Model 52 (forgot -#, he is out of town for a week).38 Special Semi-Auto for sale, used, looks to be in GREAT condition, 2 mags, black grips, no tools, no box,no factory paperwork. Finish shows little wear, no dings, scuffs, scratches or...

I got 2000 pieces of 38 special brass mixed head stamp on GUNBROKER, about 500 pieces look to be wadcutter brass. The ones that have double "canalures" are stamped: Winchester, R-P, REM-UMC, WESTERN & FEDERAL. Also, about 200 pieces are nickel plated. I was planning to load lead wadcutter...