Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

1911 Grip Bushing Problem

Discussion in 'Gunsmithing and Repairs' started by R Merrell, Apr 14, 2013.

Thread Status:
Not open for further replies.
  1. R Merrell

    R Merrell Member

    Joined:
    Feb 4, 2011
    Messages:
    6
    I have an aluminum framed 1911. Some of the grip panel bushings have stripped out, even after being installed with red Locktite. I purchase the oversized bushing repair kit from Brownells and replaced the stripped out bushings. Again, I used red Locktite when installing them. Those have also stripped out. They are stripping out when I am shooting not when I try to take the grip panels off. I tried JB weld (slow cure) to epoxy them in. I've done this three times, each time getting more aggressive with the metal prep. They keep popping loose while I'm shooting. I was informed that JB Weld is bit too brittle to handle the recoil. It was suggested I try regular epoxy. Tried this too. Same results.

    Ultimately, I would like to have a new steel frame fitted to the slide. But, my other 1911 is at the manufacturer being repaired. So, I don't want to give this one up just yet. I'm looking for recommendations on an adhesive that will hold the bushings in until I'm ready to get a new frame?
     
    Last edited: Apr 14, 2013
  2. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
  3. R Merrell

    R Merrell Member

    Joined:
    Feb 4, 2011
    Messages:
    6
    It's way too late for that now!
     
  4. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Don't know what to tell you then.

    Perhaps have the holes TIG welded shut and then re-drill & tap for a fresh do-over??

    rc
     
  5. TAKtical

    TAKtical Member

    Joined:
    Aug 8, 2012
    Messages:
    654
    Location:
    North east ohio
    Good advice rc. R Merrell, Its never too late to learn how to do something the right way.
     
  6. gunsmither

    gunsmither Member

    Joined:
    Dec 24, 2002
    Messages:
    34
    Location:
    Washington State
    Oversized Bushings from Brownells

    Check Brownells for oversized bushings and tap. Re-tap and use Red Locktite along with staking the bushings; should solve the problem. You may also possibly be able to swage the hole tighter to re- tap.
     
  7. Drail

    Drail Member

    Joined:
    Jan 17, 2008
    Messages:
    5,378
    Aluminum is for beer cans and airplanes and tent poles. But I am willing to bet that if some company started making knives or wrenches from aluminum plenty of people would buy them. (Once.) And when the customer complained of lousy performance to the manufacturer they would be told that they were either limp wristing it or it just needs more breaking in.
     
    Last edited: Apr 15, 2013
  8. Jolly Rogers

    Jolly Rogers Member

    Joined:
    Feb 19, 2008
    Messages:
    620
    Location:
    Northern Virginia
    ^ Now that right there is funny...I don't care who you are!
    I wish I had thought of it first.:D
    Joe
     
  9. R Merrell

    R Merrell Member

    Joined:
    Feb 4, 2011
    Messages:
    6
    Drail, I whole heartedly agree. I'll never buy an aluminum framed gun again. As a matter of fact, I think my solution to this might be to have the slide fitted to a new steel frame. Just need to find someone qualified to do it.
     
  10. Jim K

    Jim K Member

    Joined:
    Dec 31, 2002
    Messages:
    17,742
    I have not heard of that problem with alloy frames in general. Could you tell us what make the gun is? They must be using very soft aluminum, or there is something else wrong.

    Jim
     
  11. R Merrell

    R Merrell Member

    Joined:
    Feb 4, 2011
    Messages:
    6
    It's a Kimber CDP Pro.
     
  12. Jim K

    Jim K Member

    Joined:
    Dec 31, 2002
    Messages:
    17,742
    I know you want to keep that gun for a while, but have you contacted Kimber? They have sold a lot of those guns and this is the first time I have heard of bushings breaking out, so they might be willing to replace the frame free if the problem appears to be a defect in manufacture.

    Jim
     
  13. ApacheCoTodd

    ApacheCoTodd Member

    Joined:
    Jun 30, 2011
    Messages:
    4,609
    Location:
    Arizona
Thread Status:
Not open for further replies.

Share This Page