30/06 Data Sheet

Status
Not open for further replies.
W

wdallis

Member
Joined
Jan 12, 2011
Messages
71
Location
Tahlequah, Oklahoma
Hello, I purchased a set of 30/06 Springfield dies for reloading. They did not come with any instructions, so I am hoping I can find someone on this site who might would be so kind as to scan thier 30/06 load data and post it on here. I am new to reloading so I do not have a manual just yet. I am doing all this on a budget which is the reason why I do not have a manual with all the load data's in it, Also when I can budget in a manual, which one would you guy reccomend? Thank you.
 
I would start with a Lyman manual, It not only tells you the load data but also how to set up your dies.Lyman uses many different types of bullets in it's testing. Manuals from Bullet manufactures only show data with their bullets.Lyman also has a toll free 1 800# if you have a question.
 
3006

I have to second what was said above. I have the Lyman Manual and found it to be good. Read first and then reload.... Slowly!!!! There is a learning curve. You are going to need to start trimming the cases also. I didn't and in a CMP Match had cases sticking in the chamber and not firing due to the rounds not fitting in the chamber. Case length was TOOOOOOO Long. I didn't check the cases ( hurry ) and came close to turning a nice M1 into a paperweight. Good luck and welcome.:)
 
+1 (mega dittos)to winchester1886's post. You MUST get a manual (Lyman's is one of the best) and read the introductory sections (Lyman's 1-4) before you do almost anything else. (Go to the library if necessary)

After that, I recommend IMR4895 as your go-to powder until you get your feet firmly on the ground. (And even after many decades you'll find yourself going back time & time again to that same IMR4895)
 
I was leaning toward the lyman manual, and I have been trimming all my .270 cases to length. My .270 dies came with data sheets, but the 30/06 dies were bought used off of ebay. Life is one big training course, but I know next time to make sure that there is load data with any dies that I buy. I am using IMR4831 Powder for my .270, will that be suffecient to use with the 30/06 also?
 
I wouldn't use 4831 It's a slow burner. I use it with a 220gr in my 30-06. If you are going to use a 150gr.or 165gr. I would use 4895 or 4350. You may want to check into Hodgdon extreme powders. They are less cold sensitive.
 
I went down and checked my RCBS/LEE/Redding dies. Only Lee came with load data. I have not seen/would not expect it from any other die manufacturer, nor would I depend upon Lee data until X-checking it with other loading manuals.

Your desire to get Lyman's manual (a nice used 47th-48th edition should not set you back that much money) will never disappoint you.
 
Last edited:
Another good manuel is the Speer. They just came out with the #14. The Speer manuels have great how to sections. Before I loaded my first round of '06 (what I started on) I about wore it out reading the how to sections. 30 years later haven't broken any firearms yet.

I have a couple of bolt guns in '06 and for these I use IMR 4350. For my brace of M-1 Garands I use IMR 4064. I like CCI primers with stick powders.

'06 is going to load like the 270. I don't crimp either unless there is a crimp groove. But most of the bullets I load don't have a crimp groove.
 
I was leaning toward the lyman manual, and I have been trimming all my .270 cases to length. My .270 dies came with data sheets, but the 30/06 dies were bought used off of ebay. Life is one big training course, but I know next time to make sure that there is load data with any dies that I buy. I am using IMR4831 Powder for my .270, will that be suffecient to use with the 30/06 also?
Click to expand...
The links provided above are much more useful than the data sheet that comes with dies.

As for powder, I don't think you will like the results you get with IMR4831 in the 30-06, it's too slow a powder. I suggest you try IMR4895, H4895, Varget, IMR4064, W760, H414 or even IMR or H4350 with heavier bullets but no powder slower than 4350.
 
I am doing all this on a budget which is the reason why I do not have a manual with all the load data's in it
Click to expand...

If you can't afford a manual yet, then you should probably not reload until you can afford one. Would you buy a chemistry set without instructions?
 
I have load data for my other calibers, so why would I need a manual for just one caliber?
Click to expand...

Because, reloading manuals contain much more than just load data.
 
the hole reason for this post was to get load data, now go bark up somebody elses tree!
Click to expand...

Just trying to help. You asked a question and I gave you my best answer. The main concern anyone should have when reloading is safety. It is not generally a good idea for a new reloader to use incomplete information or use someone else's unverified load data. I was not barking up anyone's tree.
 
sorry to seem defensive, but any load data that is got from here will be cross referenced with my buddy's manual. thank you though. the reason why I dont just look at his manual, is because I am wanting ideas and what mixture has worked good for you folks.
 
Status
Not open for further replies.

Similar threads

A
  • Locked
Lee Load data
2
Replies
32
Views
3K
AshMan40
A
M
  • Locked
30-06 110 HP reloads
Replies
15
Views
4K
243winxb
243winxb
C
  • Locked
can i "mix" load data?
Replies
13
Views
662
918v
9
O
  • Locked
Which loading manual has Garand data?
Replies
8
Views
676
K-Dirt
K
C
  • Locked
need help finding 30-06 reloading data
Replies
12
Views
814
Kachok
K
Back
Top