Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Beretta M92 Mag Jam?

Discussion in 'Handguns: Autoloaders' started by Dr. Sandman, Feb 5, 2013.

Thread Status:
Not open for further replies.
  1. Dr. Sandman

    Dr. Sandman Member

    Joined:
    Jan 20, 2010
    Messages:
    527
    Location:
    Northern Indiana
    I have had my 15 round M92FS mag loaded for a while with range ammo. I went to CC it last night, so I switched the FMJ for hollow points. About halfway through unloading the mag, I noticed that the follwer must have been jammed down it there. I turned the mag upside down and loose ammo tried to fall out!! I got it unstuck with a few gentle taps, reloaded, and unloaded and it worked fine. Anybody else ever have this happen? Does one need to grease the inside of the mag or something? I have never seen this with my Glocks.
     
  2. No4Mk1*

    No4Mk1* Member

    Joined:
    Dec 25, 2002
    Messages:
    482
    Location:
    Upstate SC
    I've never had a factory mag do that. I would dissasemble and be sure it is clean and free of burrs. I never grease or oil the interior of a mag though.
     
  3. medalguy

    medalguy Member

    Joined:
    Mar 20, 2009
    Messages:
    3,199
    Location:
    New Mexico
    Same here, never experienced a problem with good mags, either factory or GI. I use a lot of GI mags BTW and they have performed as well as factory, in two different 92 models. I would NOT recommend oiling the inside of the mags, since all that will do is hold sand and grit which WILL cause a jam.

    May be just a bad mag. It happens. Set it aside for now, or continue to use it at the range and see if it jams again. Once more and I'd relegate it to the trash can. Despite the craziness, GI mags are still relatively cheap. I have about 40 of them and haven't paid more than $5 for any of them in the past. I hope those prices return soon. :rolleyes:
     
  4. MrCleanOK

    MrCleanOK Member

    Joined:
    Jun 16, 2007
    Messages:
    1,355
    Location:
    Alaska
    Is it a factory Beretta or MecGar magazine, or from a different manufacturer? How old is the magazine? More information will help us give you better answers.
     
  5. Wildbillz

    Wildbillz Member

    Joined:
    Apr 10, 2010
    Messages:
    615
    Is it a GI mag? Made by CheckMate? Early on in OIF there was a bad bunch of them that would do that. You can get a stronger replacement spring and it will fix the issue. I used to have to pull my mag appart once a week and clean it to keep it working when I was in Iraq in 04.

    WB
     
  6. brnmw

    brnmw Member

    Joined:
    Oct 26, 2012
    Messages:
    259
    Never had that happen and no don't grease the inside of the mag. I would say it's a burr most likely.
     
  7. Outlaw Man

    Outlaw Man Member

    Joined:
    Jan 18, 2007
    Messages:
    1,870
    Location:
    Cleaning my guns.
    I had a very similar problem with an old MecGar mag for my Sig 226. I think part of it was that my wife was limp-wristing a little, but I want her to be able to shoot it, too. To my eye it was free of burrs and fairly clean. I ended up replacing the springs and have had no issues since.

    If it's a burr, though, new springs may not fix it.
     
  8. Pilot

    Pilot Member

    Joined:
    Dec 29, 2002
    Messages:
    6,617
    Location:
    USA
    Inspect the mag follower. If there are any burrs or hi points, get a Dremel and buff them down. Inspect the inside of the mag for any anomolies. Do not lube or grease your mags, just clean them and if necessary replace the mag springs with Wolff +5% if they seem worn.
     
  9. Matt Dillon

    Matt Dillon Member

    Joined:
    Jan 4, 2003
    Messages:
    768
    Location:
    Houston, TX
    I would clean it and spray the interior with dry lube
     
  10. Dr. Sandman

    Dr. Sandman Member

    Joined:
    Jan 20, 2010
    Messages:
    527
    Location:
    Northern Indiana
    Thanks for all the replies. The mag came with the pistol when I bought it new, so I assume that it's a factory mag. I bought the gun maybe 2 years ago.
     
  11. Infidel4life11

    Infidel4life11 Member

    Joined:
    Nov 28, 2011
    Messages:
    621
    Location:
    Where the Army puts me
    I've had this happen a few times with Army range mags. After cleaning they worked fine, some had very worn springs and was a easy fix. Dirt and grit have always been the issue that I've ran into. DO NOT leave oil on the mag. I've used CLP to scrub them down but always made sure they were dry when I put them back together.
     
Thread Status:
Not open for further replies.

Share This Page