Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Bullet casting questions

Discussion in 'Handloading and Reloading' started by KC, Sep 27, 2003.

Thread Status:
Not open for further replies.
  1. KC

    KC Member

    Joined:
    May 22, 2003
    Messages:
    430
    Location:
    <fnord>
    Can you use lead shot to cast bullets?
    I understand that zinc contamination in lead dramatically increases the meniscus and yields unuseable bullets. It would seem that alloys in the pellet lead would also be designed for not only hardness, but to have a high surface tension to facilitate the specialized casting process, and render it unuseable for bullet casting. Is this correct?
     
  2. cdbeaver

    cdbeaver Member

    Joined:
    Dec 24, 2002
    Messages:
    473
    Location:
    Tekamah, Nebraska
    I can't contribute much about the effects of shot pellets containing zinc on bullet casting, but I'll be the first to tell you that zinc in wheel weights has a very bad effect on bullets.

    I've had to throw out about 75 pounds of wheel weights that got contaminated. I now use pure linotype metal (stuff I know something about) and have really improved the quality of my .45-70 and .30-06 stuff.
     
  3. Paul "Fitz" Jones

    Paul "Fitz" Jones Moderator - Emeritus

    Joined:
    Dec 26, 2002
    Messages:
    827
    Location:
    Northern Calif
    Lead shot

    If you have access to a lot of shot salvaged from a range then give it a try by itsself melting a pot full and see what happens when you cast some bullets.

    A lot depends on how old the lead shot is and whether it was made different back when or is a more recent formulation.

    So the only way is to try it and clean up good afterwards everything it came in contact with if it turns out bad.

    Also if it is good or bad only applies to your particular location and source.

    Paul Jones
    Moderator
     
  4. 444

    444 Member

    Joined:
    Dec 26, 2002
    Messages:
    7,978
    Location:
    Ohio
    I cast bullets all the time using currently manufactured lead shot. I cast bullets for fun, not to save money. And, to obtain bullets that would be difficult and inconvenient to obtain elsewhere. I don't have a good source of lead, so I use lead shot.
    The bullets seem to shoot fine to me. I have never seriously benchrested them, but for the relatively informal shooting and plinking I do, they seem to shoot as well as the commercial cast bullets I have purchased. They also seem to weigh what they are supposed to weigh.
    I say, do it.
     
  5. Watchman

    Watchman Member

    Joined:
    Dec 24, 2002
    Messages:
    303
    Location:
    Arkansas
    Ditto what 444 said...

    I once used a whole 20 pound bag of number 8 shot to make some 240 LSWC bullets for the .44.

    Worked great, no problems.
     
  6. Pumpkinheaver

    Pumpkinheaver Member

    Joined:
    Jun 20, 2003
    Messages:
    1,255
    Location:
    missouri
    Don't that get kind of expensive?
     
  7. 444

    444 Member

    Joined:
    Dec 26, 2002
    Messages:
    7,978
    Location:
    Ohio
    As I mentioned previously, I cast bullets for fun. Saving money isn't the idea for me. And, I don't cast enough of them to make it a money issue. I don't have a good place to cast (no garage) so I do it at a friend's garage. We don't do it all that often, so I end up buying most of my cast bullets.
     
  8. Jim Watson

    Jim Watson Member

    Joined:
    Dec 24, 2002
    Messages:
    22,349
    A friend of mine bought several hundred pounds of birdshot from a store going out of business. He added 2% tin and cast a whole lot of very accurate .45-70s out of it, even though most sources recommend against antimony in black powder bullets. He is now using the more conventional 20:1 lead:tin alloy and sees no difference in the shooting. But he only shoots BPCR metallic silhouette and midrange. Maybe the melted down shot would not have held up past 500 meters or 600 yards.
     
Thread Status:
Not open for further replies.

Share This Page