This was posted on the old version of jouster, all these posts were dumped when the site got new software.any ill reports w/ Greek HXP ?
.
According to the poster, Greek HXP cracked the receiver heel on his Garand
The bolt rebounds off the receiver heel, push that bolt too fast, and that is the end of your receiver.
I used to collect high pressure accounts with factory ammunition, but got tired of doing so.
HXP at Perry . . .
http://forums.thecmp.org/showthread.php?t=115939
HXP 77 was the culprit. I won't shoot that stuff. A whole bunch of heavy bolt handle lifts in the 03 matches when it was issued at Perry. I have fired a lot of HXP 70, 72 & 73 with no issues at all, 03's and M1's.
Tombguard, What Ceresco is implying is that while HXP 77 ammo exhibited frequent and sometimes severe issues (excessive bolt lift force, dismounted op rods, duds, hangfires, etc.) there is the concern that other lots will have the same issues but with perhaps lesser frequency. If a manufacturing process doesn't have robust QC practices, more issues are lurking out there like snakes in the grass. I am not saying that you should avoid HXP ammo - I'm just saying that one should be aware that systemically the issues might extend beyond HXP 77 ammo
In the 2007 Perry matches it was '88 dated ammo that gave a lot of 03A3 fits on opening. I keep the saved round I had in rapids beside the silver medal I earned with 29 rounds. Believe me when I tell you it was locking those bolts up TIGHT. (As in roll out of position and beat them open.)
Stiff Bolt Handle on SC 03a3
http://forums.thecmp.org/showthread.php?t=92269&highlight=high+pressure+greek
Took my SC 03a3 to the range a week ago, shooting fairly good groups at 100yds (~2MOA) with unsorted HXP. Had a problem though - occasionally the bolt handle would be VERY difficult to lift open. Never had that before with new production ammo, other sessions with HXP, and never had a problem when dry-firing (snap caps, etc). Didn't break anything evident, and everything APPEARS to function correctly. The brass all looks like I expect (There is some minor pitting in the chamber which shows on the brass, but does not effect extraction), it just felt like I needed a hammer or a crow bar to lift the bolt handle sometimes (but not always). Any ideas as to what is going wrong
Typical HXP problem. It will often be hard to chamber some rounds as well. I had 3 saved rounds in 2006 at the Western Games 1903 match when round 7 could not be extracted from the chamber and no one had a BFH handy. A wooden mallet later helped extract the round. That was in a pristine M1903 Remington with a perfect chamber. All other ammo I feed it functions perfectly. I have a 1903A3 that also has issues with HXP. About 10-20% of some lots are very long in the shoulder. I have a couple rounds that won't chamber in a 1903 at all. It almost looks like I put a No-Go gage in the chamber.
If it is only when you shoot HXP new ammo that is your problem and your answer. It's a problem that has existed with a great many bolt guns since the very first day that CMP began selling HXP ammo and has been much discussed in this forum and others for several years (and see, even today). It was a common complaint among shooters for years at the regional CMP Games and the Nationals when CMP was issuing HXP as the required ammo to use. As I stated before, in 2006, if you walked the line in every relay of the 1903 match you would see shooters having to slap bolts closed and struggle to get bolts open. Many saved rounds in rapid fire were the result and the reason for the many complaints for several years.
I doubt there is a single thing wrong with your rifle or anyone's rifle that is experiencing this problem with HXP in bolt guns. If other ammo feeds and extracts without problems you have the answer already. The long and short of it
I do have Greek HXP and the stuff is hot. And I don't think it was made that hot, don't have their specifications, have not chronographed the stuff, only shot it in bolt guns.
Which lots are hot, is all random chance. The stuff goes bad when it wants to go bad.