Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
You are using the old Black Responsive theme. We have installed a new dark theme for you, called UI.X. This will work better with the new upgrade of our software. You can select it at the bottom of any page.
I don't thing that Unique is a very good powder for 44 Mag. rifle. I understand that plated bullets like Berry's may also have their limitations as well in a rifle based on how fast you want to drive it. In my 1894 I shoot exclusively jacked bullets such as Speer 240 gr. soft points or Hornady flat points. Also, if you plan on loading up a tubular magazine I strongly suggest a bullet with a cannelure, which most jacketed bullets have in 44 mag. Clearly, they're more expensive than Berry's but I don't shoot anywhere near as many as from my Super Redhawk, so it's no big deal. I use mostly H110 which you can't download too much which means it might not be the best powder for a plated bullet. Try it and find out. 21 grains of H110 (absolute minimum load for H110) will get you a MV of about 1525 fps which is possibly pushing it for a plated bullet. Berry's has a caution about how fast you can drive their plated bullets but I don't remember what it is. AA No. 9 and Alliant 2400 are probably better powders for plated bullets. For downloading for a plated bullet I'd start around 17.5 grains for both powders. These three powders are all slower than Unique and should perform better in the longer barrel of a rifle.
Most manuals will have loads for .44 mag in rifles and for revolvers. Make sure you're using the right data. You don't need magnum primers at all. Regular large pistol primers are just fine.
Plated bullets are loaded with cast bullet data. Alliant gives 6.0 to 7.0 for a 240 grain cast FP bullet using Unique. It's one of their 'Cowboy action' loads.
If the weather holds, I'll be trying my loads out today. I found some plated bullets of an unknown manufacturer in the garage that I bought years ago. I started firing them in my handgun with really good results. They are a 240gr flat nose type and I have them loaded over 12grs of Ramshot's True Blue and standard CCI primers. That's a low power load. Just over minimum. I'll be firing them out of a Rossi Puma that I bought used. It had a broken barrel band on it and I just got that part in this week. It's kinda windy, so I won't be doing any accuracy tests, just making sure the mag tube doesn't jump out and to check for leading. I'll check back in later if all goes well.
"*How do I load Berry's Preferred Plated Bullets?
Plated bullets occupy a position between cast bullets and jacketed bullets. They are soft lead, but have a hard outer shell on them. When loading plated bullets we have found best results using low- to mid-range jacketed data in the load manual. You must use data for a bullet that has the same weight and profile as the one you are loading. Do not exceed mid-range loads.Do not use magnum loads.
*How fast can I shoot these bullets?
Velocities depend on the caliber, but as a rule of thumb, we recommend you don't shoot our plated bullets over 1200 feet-per-second. Our 44's actually shoot best around 1150 fps. 45's are generally good at 850-900 fps. Our bullets are not recommended for magnum velocities."
Well, this turned into a bust. Bullets that shoot great out of my S&W 629 were horrible out of this Puma. I'm talking 8 to 10 inch groups at 25 yards. I can almost shoot better groups with the pistol at that distance. Leading in the gun was almost non-existent. I measured the bullets at .429, so I think they may be too small for this gun. Might need .431s as bad as they shot. I'll buy a box of factory rounds just to test the gun, but looks like these bullets are for the pistol only. All in all, I'm pretty disappointed. But on a side note, my repair worked.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.