Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Modifying post-ban AR-15

Discussion in 'Rifle Country' started by HDCamel, May 2, 2012.

Thread Status:
Not open for further replies.
  1. HDCamel

    HDCamel Member

    Joined:
    Sep 7, 2011
    Messages:
    796
    Location:
    Virginia
    I found a post-ban Armalite M15A2 for a really good price. How much effort/money would it take to make it proper?
     
  2. Dr.Rob

    Dr.Rob Moderator Staff Member

    Joined:
    Dec 23, 2002
    Messages:
    14,647
    Location:
    Centennial, CO
    They are ALL post ban and it made in the USA, do whatever you want with it--provided it's not a Califiornia compliant rifle.

    You also might wish to check local ordinances about that before any modification.
     
  3. HDCamel

    HDCamel Member

    Joined:
    Sep 7, 2011
    Messages:
    796
    Location:
    Virginia
    I live in VA. No worries.
     
  4. JustinJ

    JustinJ Member

    Joined:
    Feb 15, 2011
    Messages:
    4,046
    Location:
    Austin, TX
    Its my understanding that the term "post ban" generally refers to rifles made during the AWB of 94-04. I don't recall what all it prohibited but i think there were different allowable configurations as in you can have this or that but not both.

    Anyways, just figure out what you want to change on it and ask about that specifically. You can essentially configure the rifle any way you wish so long as the barrel is >16" but even that is be doable if registered with the ATF and your local laws allow.
     
  5. HDCamel

    HDCamel Member

    Joined:
    Sep 7, 2011
    Messages:
    796
    Location:
    Virginia
    20" barrel A2 clone.
    I want a flash hider and bayonet lug.
     
  6. Dr.Rob

    Dr.Rob Moderator Staff Member

    Joined:
    Dec 23, 2002
    Messages:
    14,647
    Location:
    Centennial, CO
    You'll need to have the barrel threaded for the flash hider. That's not a 'home gunsmithing' operation for most. The bayonet lug is a simple matter of swapping out the front sight, easily done at home with simple tools. However, if you are going to have to send it to the smith for threading anyway... it's not something you have to do.

    Flash supressors and front sights are inexpensive parts, the labor is what costs $$.
     
    Last edited: May 4, 2012
  7. JustinJ

    JustinJ Member

    Joined:
    Feb 15, 2011
    Messages:
    4,046
    Location:
    Austin, TX
    Does the barrel have a break or compensator in place now? If so it may be pinned and welded on in which case the barrel is already threaded but getting the device off will be difficult at home. Also, to change the front sight post you will need to remove the muzzle device unless you cut it the current FS base off with a dremel and then install a clamp on like those made by Yankee Hill. It may be easier and even cheaper to just get a new barrel with or without FS already in place. DSA has 16" barrels on sale right now for $110. Of course you will also need a torque wrench and barrel nut wrench so after the cost of those you may be more than a gunsmith.
     
  8. HDCamel

    HDCamel Member

    Joined:
    Sep 7, 2011
    Messages:
    796
    Location:
    Virginia
    It's just a naked barrel. Only needs threading.
    Bayonet lug isn't as important.

    I don't want a 16" barrel.
    Even if I did, then I'd also have to replace the gas tube and the handguards.
    It's almost perfect as is. 20", A2 stock, fixed carry handle. It even comes with a scope mount and a cheap low power scope.
     
  9. JustinJ

    JustinJ Member

    Joined:
    Feb 15, 2011
    Messages:
    4,046
    Location:
    Austin, TX
    I was mostly referencing the DSA barrel as an indicator of how cheap barrels can be had for. Of course that one is not chrome lined and how accurate or long it will last is anybodies guess.
     
  10. Tiberius67

    Tiberius67 Member

    Joined:
    Dec 31, 2011
    Messages:
    24
    Location:
    Illinois
    Replacing the FSB is the only option to get a bayo lug on that barrel, you could send it in to a gunsmith and have the FSB replaced and the barrel threaded. Depending on who you go to, this could be the cheapest route.

    The other option is to purchase a barrel assembly with a FSB and barrel extension installed from a variety of places then put out a call for help on Arfcom's Homefront Forum for your state. Odds are someone with the tools to swap the barrel lives near you and would help you for a modest fee or even just for some beer. Then you could sell the old barrel and get some of your money back. One advantage here is you can get the barrel you want....from a USGI FN A2 barrel to a match barrel. You never know what might come up on the Arfcom EE.

    Prices for AR-15 parts are starting to get stupid as the Election approaches so I wouldn't wait long.
     
  11. fatcat4620

    fatcat4620 Member

    Joined:
    Dec 28, 2010
    Messages:
    1,263
    Location:
    TN
    Go to the ADCO website and look for the shop services section. They will be able to take care if you.
     
  12. gotigers

    gotigers Member

    Joined:
    Sep 1, 2009
    Messages:
    1,424
    +1 for ADCO

    Other than threading and FH, just shoot it. You'll figure out what you need.

    Edit: If you want a flat top upper, ADCO can probably swap yours out for less than $100. Have them ship the old upper back. Then you could sell it.
     
Thread Status:
Not open for further replies.

Share This Page