Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Need suggestions: Red Dot loads for .380 ACP, 95 grain Speer TMJ

Discussion in 'Handloading and Reloading' started by 1KPerDay, Dec 19, 2011.

Thread Status:
Not open for further replies.
  1. 1KPerDay

    1KPerDay Member

    Joined:
    Jan 19, 2006
    Messages:
    13,065
    Location:
    Happy Valley, UT
    I've browsed up a couple of threads with people saying they like red dot but can't find any current load data. Alliant's site no longer lists red dot as an option for .380 and my Hornady book doesn't either.

    Thanks for any help.:cool:
     
  2. BADUNAME37

    BADUNAME37 Member

    Joined:
    Aug 10, 2008
    Messages:
    4,434
    I looked it up in the Speer Manual 13 and they don't list Red Dot for that bullet.

    I believe I have reloaded Red Dot for my 95g Hornady XTP's. I'm going by memory as I am not at my bench.

    I suppose if one is careful, they could try that load.
     
  3. Walkalong

    Walkalong Moderator

    Joined:
    Nov 20, 2006
    Messages:
    48,860
    Location:
    Alabama
    Should work fine, but I liked AA #2 for .380. Meters like sand, and more forgiving than Red Dot. Red Dot is good stuff though.
     
  4. BADUNAME37

    BADUNAME37 Member

    Joined:
    Aug 10, 2008
    Messages:
    4,434
    I'll be right back.
     
  5. BADUNAME37

    BADUNAME37 Member

    Joined:
    Aug 10, 2008
    Messages:
    4,434
    I was mistaken.
    I load 90 Grain XTP's and also 92 grain lead Meister Round Nose.

    Both those loads I use Red Dot at 2.8 grains, they both work flawlessly through my LCP. From what I remember shooting them, they are a bit calmer than factory loads.

    I'm sorry, I do not have the starting load as it is not listed in the manual. I worked up to 2.8 and am getting 846 FPS with the XTP and 826 FPS with the heavier Meister.

    For the XTP, I also use Power Pistol at 4.6g with a velocity of 877 FPS.

    As with all loads, work up carefully, looking for signs of high pressure.
     
  6. 1KPerDay

    1KPerDay Member

    Joined:
    Jan 19, 2006
    Messages:
    13,065
    Location:
    Happy Valley, UT
    Thanks! Anyone have the older alliant load data .pdf I've seen posted here for other calibers?
     
  7. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    2002 Alliant says 95 FMJ 3.1 MAX.

    Lyman #49 says 95 FMJ 2.7 MAX.

    Hornady #4 says 90 XTP 3.3 MAX, and 100 FMJ 3.0 MAX.


    I load 3.3 with a 90 XTP for my Kel-Tec P3AT.

    It's a good load, but over what you will currently find as Max.

    rc
     
  8. kingmt

    kingmt Member

    Joined:
    Nov 17, 2009
    Messages:
    3,604
    I would start around 2gn & working up until the slide started working.
     
  9. 1KPerDay

    1KPerDay Member

    Joined:
    Jan 19, 2006
    Messages:
    13,065
    Location:
    Happy Valley, UT
    Thanks. The lee die sheet says start at 3.1 and never exceed 3.1 for 88, 90, 92 and 95 grain pills... Weird. Guess I'll start around 2.5 unless someone knows a reason why they'd say start @ 3.1...
     
  10. rcmodel

    rcmodel Member in memoriam

    Joined:
    Sep 17, 2007
    Messages:
    59,082
    Location:
    Eastern KS
    Probably because that is what the dipper they gave you dips.
    And 2.5 won't cycle a lot of guns.

    I don't know what gun you are loading for?
    But if it is a Kel-Tec or Ruger LCP, the pressure sign is guppy belly case expansion at the feed ramp cut.
    Once you start to see that, back off and regroup.

    rc
     
  11. bds
    • Contributing Member

    bds Member

    Joined:
    Jan 10, 2010
    Messages:
    15,104
    Location:
    Northwest Coast

    Attached Files:

  12. AABEN

    AABEN Member

    Joined:
    Nov 23, 2011
    Messages:
    994
    Location:
    Priceton IN
    Why do you not go get you a Pound of powder that you have load data for? What is 20 or 22 dollars if every thing goes good is it worth not blowing up your gun or hurting your self or some close to you? Why do you think there is no load data out there for red dot any more for your gun??
     
  13. kingmt

    kingmt Member

    Joined:
    Nov 17, 2009
    Messages:
    3,604
    Because they quit testing it & Red Dot is a sweet powder for .380ACP.

    Most of the powder I use there is no data for. Maybe that is why I get it at half the price of canister powder or even less.

    I have plans to start testing a powder new to me that I think is going to be even better then Red Dot. I just bought all I could find of it. Even if it isn't THE 380 powder it has other uses so no waste. If you want the name give me time to try it out & work it up then I'd be glad to post.
     
  14. 1KPerDay

    1KPerDay Member

    Joined:
    Jan 19, 2006
    Messages:
    13,065
    Location:
    Happy Valley, UT
    You really think red dot was unsafe for 40+ years before they stopped testing it for .380? It was fine in 2004 but suddenly blew up your pistol in 2005?

    I have a lot of it so I'm using it. I like it in my other pistols. It's clean and accurate and meters well for me. I know what charges my auto disc measure throws. *shrugs*


    Thanks bds and rcmodel and kingmt. :cool:

    I didn't think of that. In other powders they list different starting and max loads though.

    BTW I only have two .380s... a Ruger LCP and a SIG P230. Thanks again for the tips.
     
  15. Marlin 45 carbine

    Marlin 45 carbine Member

    Joined:
    Jul 15, 2007
    Messages:
    2,477
    Location:
    South-Western North Carolina
    I've had great results loading RDot under cast slugs for .32acp, .380acp, 9 Makarov, .357 and .45acp. 'target-practice' loads.
    for full power fmj slugs I use Power Pistol. good groups, throws a fireball flash though.
     
  16. res7s

    res7s Member

    Joined:
    Jan 18, 2008
    Messages:
    191
  17. Red Cent

    Red Cent Member

    Joined:
    May 20, 2010
    Messages:
    2,409
    Location:
    McLeansville, NC by way of WV SASS 29170L
  18. 1KPerDay

    1KPerDay Member

    Joined:
    Jan 19, 2006
    Messages:
    13,065
    Location:
    Happy Valley, UT
    Thanks again
     
  19. 1KPerDay

    1KPerDay Member

    Joined:
    Jan 19, 2006
    Messages:
    13,065
    Location:
    Happy Valley, UT
    ...

    ......
     
  20. evan price

    evan price Member

    Joined:
    Dec 7, 2005
    Messages:
    5,476
    Location:
    http://www.ohioccw.org/ Ohio's best CCW resour
    I'm using a 105-grain cast SWC with 2.7 grains PROMO (Uses Red Dot data by weight, so 2.7 Promo = 2.7 Red Dot by weight not volume!) with great accuracy.
    I'd say that would be a good start point for you and work up toward 3.0 grains.
     
  21. 1KPerDay

    1KPerDay Member

    Joined:
    Jan 19, 2006
    Messages:
    13,065
    Location:
    Happy Valley, UT
    I just tried out my first loads of red dot in .380 and even at 2.9 grains (3.1 is supposed to be max) they feel light and the slide doesn't lock back. More pleasant to shoot out of the SIG P230 than factory loads (which hurt me) but definitely nowhere close to "standard" loading. I shot them back to back with factory loads.

    Guess I'll have to break down and buy some new powder... I've been trying to make Red Dot work for everything because I have had a good supply of it.
     
  22. 1KPerDay

    1KPerDay Member

    Joined:
    Jan 19, 2006
    Messages:
    13,065
    Location:
    Happy Valley, UT
    Well I loaded 30 at 3.1 and they WORK fine but are very inaccurate, at least with me behind the pistol. (SIG P230) 4.5" at 10 yards (another group of 2.7", and 3.6" or something... this is edge to edge without subtracting the bullet diameter or whatever). definitely worse than factory Magtech ball.

    *sigh*

    The 2.8 loads were a bit more accurate but not enough for my taste. I'm using pulled speer 95 grain TMJs and mixed brass... I guess that could contribute to the crappiness of the groups. Funnily enough I shot a 1" group with my LCP and speer gold dots... that was impressive even to me.
     
Thread Status:
Not open for further replies.

Share This Page