Redding T 7 - Binding up

[gifbohane]

I have a T7 that I would not trade away. I really like it. It is a few years old. I notice that after a period of non-use the ram seems to bind going up and down. I lube a rag and clean the ram with it and it gets smooth as silk.

Anyone else have this problem? Or know why this happens and a better solution? I theorize that dirt and old primer residue slipped down into the frame where it slides through but I deprime off of the T7.

 

[Cheesemaker]

I remember getting my Big Boss II, new out of the box, - I needed to undo the the nut (s?) on the ram assembly just a tad - I did and have not had an issue since.

 

[AJC1]

Is it humid in your reloading area? A short time to cause a bunch of problems.

 

[jmorris]

Yeah, from time to time metal parts sliding against one another need lubrication or they will try and gal together (become one).

 

[CQB45ACP]

I have a T7 that I would not trade away. I really like it. It is a few years old. I notice that after a period of non-use the ram seems to bind going up and down. I lube a rag and clean the ram with it and it gets smooth as silk.

Anyone else have this problem? Or know why this happens and a better solution? I theorize that dirt and old primer residue slipped down into the frame where it slides through but I deprime off of the T7.

Mine is a couple years old and I haven’t had that problem and I DO deprime on it.

I’ve cleaned it twice. Once with gun oil wipes and the other with Balistol.

Good luck

 

[243winxb]

Break Free CLP on all moving parts. Avoid or wipe dry any priming parts/area.

 

[gwpercle]

Yeah, from time to time metal parts sliding against one another need lubrication or they will try and gal together (become one).

What jmorris said + lube with a little grease , like spray-on light grease (white lithium) ...
The grease stays put and will not dissapate like oils... wipe down and apply a coat after use , it will prevent the rust / galling when not in use and be ready to go when you crank it up again .
If you don't like using grease ... try a Dry Lube like Liquid Wrench Dry Lube L512 ...
Apply the Dry Lube spray after use , to protect from rust ... apply a little dry lube when starting back up . The grease works better but the dry lube is cleaner and doesn't attract dirt and grit ... you just have to spray a little on at start and stop ... it doesn't stick like grease but is a good rust / galling preventative
Gary

 

[CQB45ACP]

Just for fun I pulled out my copy of Redding’s operating instructions since they may have an opinion on their product. On lubrication they say:

“The ram, linkage and turret have been lubricated at the factory and your press comes ready to use. However, periodic lubrication of all moving parts is necessary to insure ease of operation and extended life. Simply use a good grade of gun oil on all pivot points and make sure the ram is kept free of contaminant build up and is lightly oiled. (Do not use oil where [is] could come in contact with live primers.) The other parts of the press require no care, other than to keep them clean and dry.”

You could do that or listen to the Internet

 

[Slamfire]

The ram on mine has turned brown due to the humidity.



Every so often I take a brass bristle brush and brush the surface, remove the primer deposits that get caked on, and otherwise knock off the little rust that develops, and clean and reoil. Also put drops of oil in the pins. Rust never sleeps!

 

[higgite]

.....I notice that after a period of non-use the ram seems to bind going up and down.......

What are you using to lube it? Could be the lube drying out or losing its lubricity over time.

 

[Rule3]

Just for fun I pulled out my copy of Redding’s operating instructions since they may have an opinion on their product. On lubrication they say:

“The ram, linkage and turret have been lubricated at the factory and your press comes ready to use. However, periodic lubrication of all moving parts is necessary to insure ease of operation and extended life. Simply use a good grade of gun oil on all pivot points and make sure the ram is kept free of contaminant build up and is lightly oiled. (Do not use oil where [is] could come in contact with live primers.) The other parts of the press require no care, other than to keep them clean and dry.”

You could do that or listen to the Internet

Your no fun!

 

[CQB45ACP]

Your no fun!

I know but thought of it since I have a T-7 also but hadn’t read the instructions.

 

[243winxb]

or listen to the Internet

Break Free CLP on all moving parts. Avoid or wipe dry any priming parts/area.

 

[Rule3]

I know but thought of it since I have a T-7 also but hadn’t read the instructions.

Heck I searched online and can not find a manual or instructions for it??

 

[Slamfire]

I know but thought of it since I have a T-7 also but hadn’t read the instructions.

Yupe

 

[AJC1]

Everyone has a favorite lube. One thing to consider is motorcycle chain wax. It's great because it stays in place, it lasts a long time, and it's a great barrier for rust. Make sure you get the wax not the lube....

 

[CQB45ACP]

Heck I searched online and can not find a manual or instructions for it??

I didn’t search beyond looking on my workbench.

 

[CQB45ACP]

Everyone has a favorite lube. One thing to consider is motorcycle chain wax. It's great because it stays in place, it lasts a long time, and it's a great barrier for rust. Make sure you get the wax not the lube....

Bicycle lubes are also excellent and aren’t dirt magnets.

 

[CQB45ACP]

Yupe


View attachment 1090382

That’s me!

 

[Blue68f100]

If the ram has a tight tolerance fit like it should grease may not be the best. Use of a light weight oil will flow better than a heavy one. Oil with the ram up then work up and down. May need to add oil if it is really dry. You could try some Kroil the oil the creep's, penetrates real good. Get it loosened up then move to a heavier oil.

 

[Eugen]

Lubing is important. A variety of lubes will work. But regular cleaning and relubing is more important.

 

[murray brook]

I don't own a T-7 but on my Lee Classic Cast I use a light gun oil on the ram every so often. Keeps it working great. I also take it completely apart once a year for a good cleaning and lube job. I assume the T-7 would benefit from the same procedure. JMO

 

[Skgreen]

75W-140

Get it loosened up then move to a heavier oil.

I'm using up that old 1/2 qt. of 75W/140 I found in the garage.

 

[wild willy]

75W-140

I'm using up that old 1/2 qt. of 75W/140 I found in the garage.

Mines 75w90 I got a little bottle been using it for 15 plus years.Works great last a lot longer then thin oils

 

[dh1633pm]

I can’t for the life of me figure out why someone would want a quality press like a T7. But if you can lift the thing, it should be good for lifetime use. A little oil does wonders for all presses. I use oil on my two presses to ensure smooth service. My older C&H press responds to lube (and lack thereof) more than my Co-Ax. I oil and then wipe up the excess.