Clark
Member
I got the RCBS rockchucker reloading kit when I started reloading in 1999:
1) Rockchucker press .. don't use it anymore, I now use Forster and Bonanza Co-ax presses with shellholer jaw housing I redesigned and made on my mill, and an RCBS Partner press.
2) "Speer 12" reloading manual... loads in it are a joke, I find my start load with Quickload software.
3) Bottle of glycerin for lube... don't use it any more, now use Redding imperial die wax.
4) Pad for applying glycerin... don't use it, I use my fingers.
5) Brush for lubing inside of case neck.. don't use it any more, I remove the expander ball so I don't need inside lube.
6) Loading tray made of plastic... don't use it. I seat bullets as soon as I charge the case, with a second press.
7) Wire brush for cleaning primer pockets. Don't use it.
8) 5-0-5 scale [Ohaus OEM]... I still use it.
9) Uniflow powder measure.... I still use it.
10) Inside outside neck chamfer [ Wilson OEM] I still use it.
11) case trimmer, don't use it anymore. I now use a Forster case trimmer or RCBS 3 way in the vertical mill
12) Funnel, don't use it, I use a Frankfort Arsenal or MTM funnel.
Other stuff I use not cross referenced to the kit:
1) Wilson Case gauge
2) Sinclair concentricity gauge
3) Lyman Moly coating kit, but with steel BBs and magnetic separation
4) Vibrators, ultra sound, and stainless steel media in a tumbler for cleaning
5) Forster and Lee priming tools
6) Lee Collet neck dies polished in my lathe.
7) Forster FL dies with necks honed out in Forster's Hardinge lathes.
8) Forster seating dies with seater stem polished on my lathe
9) Dial calipers
10) Enco set of pin gauges .0610" to .2500"
11) Enco set of pin gauges .2510" - .5000"
12) Optivisor magnifier headset
13) Dillon Super Swage 600 military crimp remover
14) Lux lamp magnifier
15) Bullets, brass, primers, and powder
16) Berry's bullets plastic ammo boxes
17) 3M Post-its for labeling.
18) Forster headspace go-gauge
1) Rockchucker press .. don't use it anymore, I now use Forster and Bonanza Co-ax presses with shellholer jaw housing I redesigned and made on my mill, and an RCBS Partner press.
2) "Speer 12" reloading manual... loads in it are a joke, I find my start load with Quickload software.
3) Bottle of glycerin for lube... don't use it any more, now use Redding imperial die wax.
4) Pad for applying glycerin... don't use it, I use my fingers.
5) Brush for lubing inside of case neck.. don't use it any more, I remove the expander ball so I don't need inside lube.
6) Loading tray made of plastic... don't use it. I seat bullets as soon as I charge the case, with a second press.
7) Wire brush for cleaning primer pockets. Don't use it.
8) 5-0-5 scale [Ohaus OEM]... I still use it.
9) Uniflow powder measure.... I still use it.
10) Inside outside neck chamfer [ Wilson OEM] I still use it.
11) case trimmer, don't use it anymore. I now use a Forster case trimmer or RCBS 3 way in the vertical mill
12) Funnel, don't use it, I use a Frankfort Arsenal or MTM funnel.
Other stuff I use not cross referenced to the kit:
1) Wilson Case gauge
2) Sinclair concentricity gauge
3) Lyman Moly coating kit, but with steel BBs and magnetic separation
4) Vibrators, ultra sound, and stainless steel media in a tumbler for cleaning
5) Forster and Lee priming tools
6) Lee Collet neck dies polished in my lathe.
7) Forster FL dies with necks honed out in Forster's Hardinge lathes.
8) Forster seating dies with seater stem polished on my lathe
9) Dial calipers
10) Enco set of pin gauges .0610" to .2500"
11) Enco set of pin gauges .2510" - .5000"
12) Optivisor magnifier headset
13) Dillon Super Swage 600 military crimp remover
14) Lux lamp magnifier
15) Bullets, brass, primers, and powder
16) Berry's bullets plastic ammo boxes
17) 3M Post-its for labeling.
18) Forster headspace go-gauge
