Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Safe to fire deep seated bullet?

Discussion in 'General Gun Discussions' started by Dbl0Kevin, Oct 7, 2004.

Thread Status:
Not open for further replies.
  1. Dbl0Kevin

    Dbl0Kevin Member

    Joined:
    May 26, 2004
    Messages:
    1,183
    Location:
    SC
    In the course of loading and unloading guns to take to the range, clean, etc. I've often found the first round will sometimes have the bullet pushed farther down into the casing than the rest. I've usually just tossed these rounds after they've gotten visibibly lower, but as it's usually the expensive defense ammo this happens to I've been wondering if it even makes a difference. So does it?
     
  2. El Cid

    El Cid Member

    Joined:
    Mar 11, 2004
    Messages:
    27
    Location:
    In the Ozarks
    It depends on how deep. A minor amount like 1/8 inch shouldn't hurt. Any more and I use an inertia bullet puller to bring the bullet out to it's proper place, then recrimp.
     
  3. Redlg155

    Redlg155 Member

    Joined:
    Dec 25, 2002
    Messages:
    2,724
    Location:
    NW Florida
    I usually dispose of any ammo with the bullets seated deeper. It's not worth taking a risk.

    You also have to consider that a great many of us use +P or +P+ ammo. Those are already above standard pressure limits, so you definitely don't want to mess with any deep seated bullets.


    Good Shooting
    Red
     
  4. Fatcat

    Fatcat Member

    Joined:
    Jan 1, 2003
    Messages:
    109
    Location:
    Corvallis, OR
    NO.

    The bullet setback decreases the volume of the case, which increases firing pressure. This is potentially dangerous.

    I'd toss em just to be safe.
     
  5. Standing Wolf

    Standing Wolf Member in memoriam

    Joined:
    Dec 24, 2002
    Messages:
    24,041
    Location:
    Idahohoho, the jolliest state
    I've been shooting short rounds for decades.

    If you doubt the safety of it, consider the .38 special round for the old Smith & Wesson model 52 semi-automatic pistol. Hollow-based wadcutters were seated below the crimped case mouth over 2.8 to 3.5 grains of Bullseye, one of the faster powders on the market.

    I've shot short rounds in every caliber from .38 special through .44 magnum without a problem—other than .45 A.C.P. rounds that don't feed smoothly, to be sure.
     
  6. GigaBuist

    GigaBuist Member

    Joined:
    Sep 27, 2003
    Messages:
    2,261
    Location:
    Grand Rapids, MI
    From what I've gathered on THR if it's .40S&W don't even think about it.
     
  7. garrettwc

    garrettwc Member

    Joined:
    Dec 24, 2002
    Messages:
    1,025
    Two words.

    Ka...Boom!

    I have seen this on a 1911. Poor crimp on reload caused excessive setback. Blew the mag out of the gun and split the left side grip panel. Peppered the shooters face with shards of brass. (Always wear eye-pro).

    Get rid of them.
     
  8. cracked butt

    cracked butt Member

    Joined:
    Jan 3, 2003
    Messages:
    6,986
    Location:
    SE Wisconsin
    Nope.

    Your fingers, gun, eyes, are worth way more than that cartridge.
     
  9. Shalako

    Shalako Member

    Joined:
    Dec 30, 2002
    Messages:
    629
    Location:
    The most tactical cubicle in Sacramento
    When I first got my Springfield 1911, the combination of a rough feed ramp and those slippery Winchester silvertips resulted in bullets being pushed into the case at least 3/16". Luckily I caught this upon chambering rounds at home before attempting to fire them. That might have been a bad scene, but I'll never know.
     
  10. Vern Humphrey

    Vern Humphrey Member

    Joined:
    Dec 30, 2002
    Messages:
    18,691
    Location:
    Deep in the Ozarks
    Quote:
    -------------------------------------
    If you doubt the safety of it, consider the .38 special round for the old Smith & Wesson model 52 semi-automatic pistol. Hollow-based wadcutters were seated below the crimped case mouth over 2.8 to 3.5 grains of Bullseye, one of the faster powders on the market.
    -------------------------------------

    Wait a minute! Wadcutter loads are DEVELOPED to be loaded flush with or below the case mouth -- which means they are pressure-tested to ensure that pressures with the deep-seated bullet do not exceed SAAMI standards. In fact, most such loads are well below SAAMI maximums.

    The defense ammo you buy is NOT tested for deep-seated bullets. It's typically loaded right to SAAMI maximums, and shooting a deep-seated bullet is definitely going to push pressure over SAAMI maximums.

    I have no problem with pulling the bullet out to original seating depth with taps of an inertia bullet puller and recrimping -- but shooting a deep-seated bullet is a good way to damage your gun -- and maybe lose some body parts in the process.
     
  11. goon

    goon Member

    Joined:
    Jan 20, 2003
    Messages:
    7,251
    I'd say no. Depending on what you are shooting, the ammo cost anywhere from a few cents to a few bucks a round. Is it really worth it to risk destroying a gun that costs hundreds or thousands of dollars and risking injury to yourself of others just to save a few cents?
     
  12. Gunpacker

    Gunpacker Member

    Joined:
    Jan 24, 2004
    Messages:
    532
    Location:
    Tampa, FL
    Wadcutter 38

    Just remember also that the wadcutter loads are wimp loads to start, and are for accuracy and low recoil. They are only about 700 fps and are far from max pressure to begin with. Definitely not a valid comparison.
     
  13. mete

    mete Member

    Joined:
    Dec 31, 2002
    Messages:
    3,579
    Location:
    NY
    For a .40S&W if you push the bullet back 0.1" you will DOUBLE the pressure. That's from 35,000psi to 70,000 . it's spelled KABOOM.
     
  14. entropy

    entropy Member

    Joined:
    Feb 9, 2004
    Messages:
    4,301
    Location:
    G_d's Country, WI
    One Cartridge: @ 50 cents

    Pistol: @ $400

    Keeping all your fingers attached to your hand: Priceless.

    Don't do it. It's not worth it. Better you should find out why they are getting pushed down, and fix the problem. I kept trying to fire them from my Kel-Tec 9mm carbine. I'm pleased to announce I still have all my fingers, tho' they were numb for a while!:what:
     
  15. Arc Angel

    Arc Angel Member

    Joined:
    Feb 9, 2004
    Messages:
    101
    :rolleyes:
    This is positively NOT A SAFE PRACTICE with any of the modern, 'high pressure' rounds; e.g., 40 S&W, 10mm, 357 SIG, or the latest 45 pistol aberration: the 45 GAP.

    Especially inside a plastic frame pistol it spells, 'kaBoom!' :D
     
Thread Status:
Not open for further replies.

Share This Page