Search results for query: *

Hello, Can anyone give me a recommendation on a guide / outfitter for a South Dakota Prairie Dog Hunt? I have looked on Ultimate Prairie Dogs and I have made some phone calls. I always feel better about it when I have an unbiased opinion from someone with first hand experience. I am more...

Hello all, I am looking for suggestions on a free float hand guard for an AR 15 varmint build. I am using a 24 inch bull barrel with a .936 gas block journal. I haven’t decided if I will use a low profile gas block or an exposed gas block just yet. I am after something pretty simple. Key...

Hello I recently acquired a matched upper and lower receiver. Dose anyone know which set screws adjust for trigger creep and which adjusts for upper / lower tension?

Hi, My wife just bought a Glock 42 and she needs a belt and a holster. She is not big on the idea of wearing a belt, but I will convince her that it is necessary. I don't think she should carry off body in a purse or fanny pack. So what would your suggestions be for a good belt and...

Hello, I just bought a Kahr PM9 for concealed carry. I am looking for an IWB holster to be worn behind the hip. I'd like the backing of the holster to be either horsehide or cowhide. I want it to be easy to remove from my belt without having to remove the belt. The holster itself could be...

Hi All, I received this rifle a couple of weeks ago after a 17 month wait. I almost cancelled the order several times. I had the chance to fire the rifle last weekend. Here are some of my impressions. The first thing I did to the rifle was remove the Magpul PRS stock that I ordered...

Hi all, I just picked this rifle a few days ago. I am very excited about it. The rifle was made in 1999 and it appears to be very lightly used. I just ordered a bottom picatinny rail and a new Ops 2 top rail. I also ordered a Vortex PST 4 - 16x50 scope and Night force Ultra light rings...

Hi, I just starting reloading 9mm and have to say that I sort of hate. Tiny components that don't like to stay still in my progressive press. If my powder dies is not perfectly aligned with the brass I crush cases. Putting that little bullet on that little case sucks too! Give me .45 or...

Hi, I have a pretty good collection of modern handguns. I think I would like to add a vintage firearm such as a WWII era German Luger. I would want the pistol to be a shooter. Number matching would be nice, but not a requirement. My primary concern would to have a pistol made by one of...

Hi all, I have a custom built .308 built on an AICS chassis and I recently finished modifying my Armalite AR 10T to include an AR Gold trigger. I understand the inherent accuracy in the bolt action, but both of these rifles are shooters! So my question to you all is which of these...

Hi All, I will be picking up my new Armalite AR 10T later this week. I just received a Daniel Defense 7.62 lite rail in the mail today. I will also be receiving a Armalite upper receiver vice jaw clamp and a PRI Armalite barrel but wrench. I have heard that the factory Aramlite barrel nut...

Hi all, I ordered this kit and finally got through the installation. It took me three days and two orders for additional parts. Here is a run down of the installation. First you have to remove the rear sight to replace the safety plunger and spring. Removing the rear sight was awful. I put...

Hi, I recently bought a CZ 527 .223 with a laminate stock. I have been working to get all of the pieces together. I bought a recontoured bolt handle from Custom Reloading Tools. I than struggled to get that part on and than struggled to shave down some of the stock to get it to clear. I...

Hi, Does anyone here reload this cartridge. When you reload a 325 grain bullet, what measurement to you get right at the top of the brass? I am trying to determine if I have enough crimp. Thanks! CB

Hi, Does anyone have any first hand experience with this scope? I hear the glass is top notch. What I am concerned with is the quality of the clicks on he target turrets. I heard someone say they are mushy. It is a two hour drive into NYC to handle one of these scopes myself. I'd don't...

Hi all, I have this rifle on the way in .223. I also ordered Leupold medium 30mm rings and a Reloading Tool Company recontoured bolt My question to you all is if money isn't too much of an issue, what scope would you buy for this quality of a rifle. I have read that the rifle is pretty...

Hi All, So I took my Savage rifle in 22-250 to the range today and noticed that there is a little piece of rubber which sits right at the base of the bolt handle on the back side. Appears to be some sort of a bolt handle stop /cushion. It was coming loose. Any idea what caused this? I just...

Hi all, I just bought this rifle on Gunbroker! I need advice on scope rings and or bases that will clear the bolt. Should I just get rings or rings and bases? I know the rifle has built in bases, but I was wondering about a picatinny rail. Exactly what brands and specs would you...

Hi all, I am looking for a new hunting rifle in 270 WSM. I don't need a left handed rifle, but the rifle has to be stocked for a left handed shooter. This means no monte Carlo stocks with a right hand cheek piece or a grip with a right handed palm swell. I am willing to spend in excess...

Hi, So I decided I'd better get going and reload a bunch of .223 ammo. I started just before Christmas and after just a few cases, I managed to break a decapping pin from my resizing die. Unfortunately I did not have a spare. Dillon precision sent me two spare pins which arrived today. I...