Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Anyone use Bartlett Reloaders supply?

Discussion in 'Handloading and Reloading' started by BsChoy, Jul 22, 2007.

Thread Status:
Not open for further replies.
  1. BsChoy

    BsChoy Member

    Joined:
    Jun 14, 2005
    Messages:
    1,344
    Location:
    Upstate NY
    Anyone use GIbrass.com?

    I think he also goes by GIbrass as well. I am preparing for the OSHA onslaught and want to buy a good amount of reloading gear. He has non pull down 4895 (but says closer to 4064 which is fine by me) 100.00$ per 8lb jug? Sounds good but I was wondering if anyone else has a 4895 pull down that I might get for cheaper since the rest of his pwders are pull down and go for 40.00 per 8lb jug? 100.00 ain't bad but every little bit helps?
     
    Last edited: Jul 22, 2007
  2. NuJudge

    NuJudge Member

    Joined:
    May 20, 2006
    Messages:
    748
    Location:
    SE Michigan
    OSHA has withdrawn its proposed rulemaking.

    I've bought a good bit of stuff from GI Brass, when prices were a lot lower. The surplus 4895 is just a couple dollars less an 8-pounder than new from Powder Valley. With new powder, there is none of the uncertainty as to burn rate or powder life expectancy. YMMV.

    CDD
     
  3. bender

    bender Member

    Joined:
    Aug 10, 2006
    Messages:
    970
    Location:
    TX
    Haven't ordered any powder or primers from him, but I've ordered lots of brass & bullets.

    Seems friendly, and has good service.
     
  4. sargenv

    sargenv Member

    Joined:
    Apr 6, 2006
    Messages:
    382
    Location:
    Bay Area, CA
    A lot of the $40/8 pounds are for rifle with quite abit larger bore. We're talking powder for 50 BMG and other large calibers where a very slow powder is useful. It's not meant for smaller caliber standard ammo. I've ordered surplus from him in the past and would if he got in powder I found useful.
     
  5. USSR

    USSR Member

    Joined:
    Jul 7, 2005
    Messages:
    8,451
    Location:
    Finger Lakes Region of NY
    BsChoy,

    You missed out on the last of the "reasonably priced" IMR4895, last year at $78 per 8#. Have not seen anything else on the market, and like was previously said, the $40 stuff is much too slow for medium bore use.

    Don
     
  6. BsChoy

    BsChoy Member

    Joined:
    Jun 14, 2005
    Messages:
    1,344
    Location:
    Upstate NY
    Maybe its for the better...it meant testing in all my guns again...the wife wouldn't think to highly of that idea!
     
  7. snuffy

    snuffy Member

    Joined:
    Apr 4, 2004
    Messages:
    2,894
    Location:
    Oshkosh Wi
    I've dealt with Jeff Bartlett a lot over the past 6 or so years. He's a great guy to deal with. I've not had a single problem with ANY of his powders. It seems right now though, he's having a tough time getting anything to sell.
    http://www.gibrass.com/
    Pats reloading usually has a lot more choices than Jeff does. Dunno why that is, but I've never ordered anything from Pat.
    http://www.patsreloading.com/patsrel/whatsnew.htm
     
  8. USSR

    USSR Member

    Joined:
    Jul 7, 2005
    Messages:
    8,451
    Location:
    Finger Lakes Region of NY
    Have ordered from both Jeff and Pat, and they are GTG.

    Don
     
Thread Status:
Not open for further replies.

Share This Page