Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
You are using the old Black Responsive theme. We have installed a new dark theme for you, called UI.X. This will work better with the new upgrade of our software. You can select it at the bottom of any page.
Most of what i load is lead that is lubed with wax. Its dirty stuff and it builds up in the seating die. The threads get gummed up and it can be hard to turn and especially tighten down when it really builds up. You do have to take out the seating plug/stem and knob and get in there and clean it out with a dowel or something else. Whats left over I use a brush with acitone to get the rest. Gotta do that at least ever 1 thousand rounds. I've heard brake cleaner works well but have not tried it. Use eye protection!
I also use Lee dies. FMJ may build up some dirt from the case over thousands of rounds but its a non issue mostly.
Just clean them like a gun. Some solvent and a brush . I spray some silicone in the,m and blow out with compressed air..
Word of advice, do not take the resizing /depriming die apart. There is no need to remove the top collet nut as it is a really pain to put back in. If you must , just loosen it with a 1/2" wrench on the nut and a 3/4" wrench on the dies body. The pin will then fall out. (same for removing a stuck 223 brass)
Yup, unless you are loading lead bullets they will usually stay fairly clean. Spray with cleaner, wipe out with a pistol rod and a proper size patch or brush. Pistol dies for lead bullets get soaked in solvent once in a while to keep em seating correctly.
I take mine apart and dump them in the tumbler with corn cob media with some Nu-Finish car wax when they get rusty on the outside. Otherwise clean them with a bit of carb cleaner and a brass brush as needed. Worked for me for over 40 years so far.
Thanks guys, I dont do cast lead, but use hornady wax or imperial wax, and I saw a thread where someone sent a die with stuck case back to I believe RCBS, who said 90% of the stuck case/dies they get are from being gummed up with wax lubricants, and did not recommend them.....thoughts?
Stuck cases are caused by no case lube, or not enough case lube.
No matter what kind of lube it is.
Nothing more, or less.
Wax case lube, or oil case lube simply cannot 'build up' in a sizing die.
The pressure involved in sizing will squish out just about anything you put in there.
Except high grade sizing lube of one type or another.
But regardless of that, it does not build up in a sizing die and cause stuck cases!
The only possible problem excess lube or wax can cause is shuolder dents in bottle-neck rifle cases.
I reload a lot of cast and as such, lube gets all up in there an gunks up the works. I usually disassemble, toss in the ultrasonic cleaner and run a cycle. Brush them out and run through another cycle. Come out looking brand new. Blow off with compressed air, a light rem oil coat and wipe with clean dry towel and load up some more.
I know when to clean when the old lube starts getting everywhere.
yep take them a part. solvent and brush. ive even put them in ultrasonic if they got rusty or bought some that some neglected. I take mine apart once a year for 2 reasons, 1 to clean them, 2 to inspect them.
its always good to take them apart to inspect things every once and a while.
I disassemble them and use a clp on my Lee dies but use brake cleaner on my RCBS, Hornady, Herters and Lyman. I worry about the brake cleaner affecting the o-rings in the Lee dies. After they're clean, I'll give them a shot of Rem oil if they won't be used for awhile.
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.