Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Favorite Case Lube For Rifle Brass? RCBS X-Die - 223 Rem

Discussion in 'Handloading and Reloading' started by duncan, Dec 29, 2002.

Thread Status:
Not open for further replies.
  1. duncan

    duncan Member

    Joined:
    Dec 29, 2002
    Messages:
    515
    Location:
    Seattle, WA
    What is your favorite lube?

    Thinking about getting some Lee .223 rem dies and some Lee case lube.

    Hornady One Shot Spray Lube seems too thin. Been getting some cases stuck in my RCBS X-die. So I may be making several switches.

    Your experiences with the X-die? Sent mine back to RCBS once and they asked me to send again. getting expensive.

    Lube?
     
  2. happy old sailor

    happy old sailor Member

    Joined:
    Dec 29, 2002
    Messages:
    581
    Location:
    WestArk
    my favorite is anhydrous lanolin. sheep grease without water. ask a pharmacist. unlike petrochechemicals, it is great for your skin. a couple ounces will last and last. cheap too.
     
  3. larryw

    larryw Member

    Joined:
    Dec 22, 2002
    Messages:
    1,655
    I like the Dillon case lube. Does a good job for me without being messy.
     
  4. Mike Irwin

    Mike Irwin Member

    Joined:
    Dec 22, 2002
    Messages:
    7,956
    Location:
    Below the Manson-Nixon line in Virginia...
    I was going to suggest the One Shot. Never had any problems with it, other than the cost.
     
  5. Pointman

    Pointman Member

    Joined:
    Dec 26, 2002
    Messages:
    283
    Location:
    Indiana
    Imperial Sizing Wax
     
  6. cheygriz

    cheygriz Member

    Joined:
    Dec 28, 2002
    Messages:
    2,245
    Location:
    High up in the Rockies
    I no longer use anything other than Dillon spray on lube. It works well for everything.

    BTW. My preferred method is to spray the cases and then let them dry, rather than sizing them wet. Either method works well, but letting them dry first is less messy. And since retiring, I do not allow myself to get in a hurry.

    I clean the lube off of the cases by tumbling in warm water and liquid Tide. It works for me.

    Wiping them off with a soft cloth soaked with alcohol works well too, but it's a PITA.
     
  7. mbott

    mbott Member

    Joined:
    Dec 25, 2002
    Messages:
    351
    Location:
    Central, OH
    I use Hornady's One Shot. Although I plan to try the following "home-brew" from the old RELOAD-L list:

    1 part Lanolin
    8 to 12 parts isopropyl alcohol (experiment)
    shake well before use

    --
    Mike
     
  8. Tom A

    Tom A Member

    Joined:
    Dec 26, 2002
    Messages:
    14
    Location:
    NV North
    I use the RCBS lube, applied to the inside of the neck with a nylon bore brush. Use same externally with the lube pad that came with my Rockchucker kit. I've never stuck anything using this lube. I run the cases through a dishwasher cycle after sizing to remove the lube.

    I've done several hundred rounds of .223 so far with the X-die and am very happy with not having to trim the cases. Seems to work as advertised.
     
  9. Gewehr98

    Gewehr98 Member

    Joined:
    Dec 24, 2002
    Messages:
    5,988
    Imperial Sizing Die Wax

    Pretty darned slick stuff, and it's great for serious case forming! I still use Dillon spray-on case lube for bulk ammo loading through the progressive presses, but otherwise, it's Imperial all the way!
     
  10. Zero

    Zero Member

    Joined:
    Dec 25, 2002
    Messages:
    99
    Location:
    Miami
    Dillon Case Lub

    I don't know about the rest but the Dillon case lub is Lanolin and Alcohol. Best to spray and let some of the alcohol evaporate then you are left with a nice slick surface for your sizing. It's completely natural and non-toxic.
     
  11. Bottom Gun

    Bottom Gun Member

    Joined:
    Dec 26, 2002
    Messages:
    812
    Location:
    Elgin, Arizona
    I use the Dillon spray lube.

    I tried some X dies in 30-06 and wasn't happy with them. I was getting lube dents on each case shoulder. The little bleed hole in the sizing die doesn't work. Yes, I checked to make sure it was clear of obstruction.
    I called RCBS and their support guy told me I had to wipe the lube off the shoulder of each case.
    What a pain in the a**!!!
    I called Dillon and ordered a set of their dies. They work exactly like they're supposed to and I haven't had any lube dents since.

    I'm starting to wonder about RCBS. I've used their equipment for a lot of years but lately I haven't been happy with their offerings, their digital powders measures and their priming tools to be specific.
    RCBS customer service is pleasant to deal with, but they never seem to be able to solve the problem.

    My two cents.
     
  12. Poodleshooter

    Poodleshooter Member

    Joined:
    Dec 30, 2002
    Messages:
    1,237
    Location:
    Mr. Jefferson's country
    I've been using the RCBS oil based lube, along with their rolling pad. I roll about 10 of them at a time through a thin layer of the stuff on their sponge pad. I get occasional dents in the first batch, but it's quick and easy, and lasts longer than the cans of spray lube. Add to that, I never lube the necks, inside or out; just the case bodies. I've loaded several thousand .223,.308 and even 7mmRM this way, and have never stuck a case in my Lee die with this method.
     
  13. ms1200

    ms1200 Member

    Joined:
    Dec 24, 2002
    Messages:
    62
    Location:
    midwest
    i use rcbs caselube 2 and a lube pad
     
  14. Shoney

    Shoney Member

    Joined:
    Jan 1, 2003
    Messages:
    1,292
    Location:
    Transplanted away from MT
    After over 40 years of reloading, I've tried most everything that came along. Nothing does as well as

    IMPERIAL SIZING DIE WAX

    Nothing else will do.

    Shoney
     
  15. GinSlinger

    GinSlinger Member

    Joined:
    Dec 27, 2002
    Messages:
    130
    Location:
    Hill Country, Texas
    I have been informed and have read that STP is a great case lube. Yet I do not see it in this thread. Am I wrong? Had planned on using STP after running out of Lee.

    GinSlinger
     
  16. cheygriz

    cheygriz Member

    Joined:
    Dec 28, 2002
    Messages:
    2,245
    Location:
    High up in the Rockies
    STP is a great case lube. It's a royal PITA to get off though, both from your cases and your fingers. but it does a great job.
     
  17. happy old sailor

    happy old sailor Member

    Joined:
    Dec 29, 2002
    Messages:
    581
    Location:
    WestArk
    Shoney, have been reloading for 40 or so myself. why i have never tried Imperial Wax i do not know. thanks to your recommendation, i will do so.

    one gets in a rut and needs a wakeup. ty
     
  18. Bill Adair

    Bill Adair Member

    Joined:
    Jan 2, 2003
    Messages:
    84
    Location:
    Seattle/Tacoma area
    GinSlinger,

    Isn't STP petroleum based?

    I thought powder and primer exposure to petroleum products was problematic, unless the cases are very thoroughly cleaned after sizing?

    The Hornady spray lube works well for me, but I have to rotate the cases while spraying, to get an even coat.

    Also have to let the carrier evaporate completely, before sizing.

    Bill
     
  19. WalkerTexasRanger

    WalkerTexasRanger Member

    Joined:
    Dec 31, 2002
    Messages:
    289
    Location:
    Houston, TX
    Imperial Sizing Wax. No need to look further...
     
  20. P95Carry

    P95Carry Moderator Emeritus

    Joined:
    Jan 3, 2003
    Messages:
    16,341
    Location:
    South PA, and a bit West of center!
    Long ago I used to use STP!! But a tad oily for clean up. For some now have used the Lee stuff .. no complaints on that .. and by all accounts it is based on a machining lube, so able to tolerate high pressures ... seems to do well and is non greasy .... just a wipe of case with cloth does fine. Usually do the tumbling earlier on b4 sizing.
     
  21. Paul "Fitz" Jones

    Paul "Fitz" Jones Moderator - Emeritus

    Joined:
    Dec 26, 2002
    Messages:
    827
    Location:
    Northern Calif
    Home Made Case Lube

    Many years ago I worked at a gun shop while in high school to earn very interesting things. They made and sold their own case lube that was red and I think it was a mixture of red automotive transmission fluid and possibly had some lanolin added. I still have a quart of it and the other quart has lasted me for 50 years.
     
  22. P95Carry

    P95Carry Moderator Emeritus

    Joined:
    Jan 3, 2003
    Messages:
    16,341
    Location:
    South PA, and a bit West of center!
    Sounds like a good brew Paul ..... one I have heard of before. Lasted you 50 years eh? Hmmm .. you might even be older than me!!:p
     
Thread Status:
Not open for further replies.

Share This Page