marlin .30-30 finally ? on 336C and 336W

Status
Not open for further replies.
S

shotgunsrfun

member
Joined
Oct 25, 2009
Messages
260
Location
NRA member
close thread now please :)

What is the main difference in the model 336C and 336W I know the difference in 336SS but I see the 336w has a gold trigger and a mounted scope mount already, is that all it is different in the gun models? can you still shoot normal iron sights with this mount?:confused:

I just found the only 2 models in the region. LOL
 
Last edited:
You can easily remove the scope mount from the "336W" if you want.

336C is Walnut

336W is "hardwood" made to look like walnut, with gold trigger.

I think the "C" also has 2 screws holding on the front sight while the "W" uses only 1. This may be an issue if you want to install an aftermarket front sight such as the XS sight which replaces the entire front sight, ramp and all.

I prefer the 336C myself although the walnut isnt anything to write home about.
 
The C has a much more expensive walnut stock. Fluted comb, and a grip cap. The W has a cheaper birch stock. The metal on the W may not be polished quite as well, but there is very little, if any difference there. At one time the iron sights used on the W were not as well made, but they have changed several times, so I'm not sure what they are putting on the new ones.

Both should be equals in reliability and accuracy. I much prefer the C to get the walnut and would buy a used version if needed to save money. I feel in the long term it is a better investment. But that is just me. The W will shoot just as well.
 
If I had the choice the W only is it still a good rifle? You said the metal on the way may not be polished quite as well ? :/
 
I think on the 336c it is rubber buttpad and 336w it is HARD rubber buttpad.

I mean it is a little bit different but it shouldnt mean the internal parts are made less quliaty?
 
In addition to the differences already noted, the W comes with a sling. I see no difference in the finish on the metal parts.
The guts are identical and the only MAJOR difference is the furniture, and that's what you're paying extra for.
 
shotgunsrfun,

there should be no difference in quality or performance between these 2 models at all. the primary difference is cosmetic in nature. the walnut on the "C" model looks a bit nicer than the wood on the "W" model. i cannot say the difference in sight screws or grip caps as i honestly have never noticed.

as far as the finish on the metal, there may be some difference, but if there is i cannot tell it. they look about the same to me, but i am no expert.

i have also heard that the wood on the "W" model is harder than the Walnut on the "C". Probably makes very little difference though.
 
Thanks for the help. I always wonder on different models is there something MAJOR different(gut parts cheaper made or something) I see it does come with a sling. I really do not mind the wood its not ugly. I am glad this rifle is made in the USA.

One last question, does it matter what grain you use in the gun?
 
Like any gun, each rifle will shoot ammo differently. The only way to know is to shoot different ammo and see which your riflel "likes" best.

Personally I've always found 150 grain to shoot well out of my 336's including my current "W" model.

I've owned two "C's" over the years and my current "w." Other than the wood, I can't tell any difference.
 
Found this at wiki answers:

The 16 1/4" Marlin 336 was called the "Marauder" in catalogs for 1963-64. That is the only two years they were offered. They are desireable guns, and somewhat rare. If in excellent condition they can bring bonus values of 25-30% over std. model carbines
Click to expand...

True? And any others? Thanks.
 
The Mauraders were made in the 60's, but Marlin also made a LTS version during '88 and "89. They are essntially a more modern Maurader with a 16.25" barrel. The only real difference is the addition of the crossbolt safety and a square lever. I'm not sure of the production numbers on the Maurader, but only around 2,700 LTS rifles were made. I've only seen 1 LTS and I own it. I've seen several Mauraders over the years, but have not been willing to pay the collector prices for them.

Marlin made quite a few straight gripped versions up through the 70's. They are commonly refered to as "Texan" models, but all I have seen have no special designation on them. I have 1 made in 1958 and 3 from the 70's. (I much prefer the straight grip Marlins if you cannot tell). I know where another is located, but have been putting off adding it to my collection. Almost all of these have 20" barrels, but they made them with 18.5" barrels for one year I think. I had 1 of those years ago and like a fool let it go. They may be the most rare. I see 4-5 of the 20" Texan versions each year cruising gun shows and pawn shops, but that is the only 18.5" version I've seen.

Marlin also made the Spikehorn with a 16.5" barrel and a pistol grip cut shorter as a youth rifle. Not sure of the years, early 2000's I think. They are no longer made and I have no idea on numbers, but would bet they did not make many. This is not an all inclusive list. Just the ones I am aware of.

During 2005 Marlin made a 336SS-LTD. They made 500 blue and 500 stainless. They are essentially a guide gun chambered in 35 Rem. I bought one of the stainless versions. They have an 18.5" barrel and straight grip.

Marlin is currently offering some special versions with different barrel lengths and other features, but I'm not up on the newer models. Not sure I'm willing to pay the prices they are asking for the newer ones either.
 
Last edited:
Status
Not open for further replies.

Similar threads

A
  • Locked
Marlin 336: C v. W?
2 3
Replies
55
Views
43K
streakr
S
Z
  • Locked
Which model do I own?
Replies
5
Views
423
Quoheleth
Quoheleth
G
  • Locked
Marlin 336 "W"?
Replies
13
Views
8K
Fred Fuller
F
S
  • Locked
Marlin 336C in 30-30, what's it worth?
Replies
13
Views
1K
zero_chances
Z
L
  • Locked
Marlin 336 vs Revelation 200
Replies
4
Views
907
LSMS
L
Back
Top