Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

One piece scope mount&base for bolt action?

Discussion in 'Rifle Country' started by jlewis406, Feb 3, 2013.

Thread Status:
Not open for further replies.
  1. jlewis406

    jlewis406 Member

    Joined:
    Jun 28, 2012
    Messages:
    37
    Location:
    New Mexico
    I have no idea if such a thing exists...but I am looking for a one piece scope base with integrated 30mm rings for a Remington 700 Short Action.

    What I am thinking of is something like the Burris PEPR or the KAC one peice scope mount I have on my AR, but designed for a bolt action. So instead of channels for the rails the base just screws into the action like a traditional scope base, but has integrated rings. I am just looking for something will less points of failure. Thanks gents.
     
  2. fgr39

    fgr39 Member

    Joined:
    Jan 1, 2003
    Messages:
    350
    Location:
    MD
    look at the DNZ gamereaper setup, not sure if they have 30mm, but they are great.
     
  3. 119er

    119er Member

    Joined:
    May 3, 2011
    Messages:
    672
    Location:
    Houston
  4. jlewis406

    jlewis406 Member

    Joined:
    Jun 28, 2012
    Messages:
    37
    Location:
    New Mexico
    Man, I am thankful for the power of the internet. That's pretty much what I am thinking of!
     
  5. Loc n Load

    Loc n Load Member

    Joined:
    Jan 2, 2013
    Messages:
    208
    Location:
    Indiana
    1 pc mount and base

    I use a GG&G one pc mount with throw levers on several of my rifles, these mount on any 1913 rail...which can be obtained for most rifles....I have used the GG&G mount for several years on several rifles and carbines that have seen a lot of hard use.....they maintain their zero when taken on and off and they are built like a tank.....I like the throw levers on AR's or even on some of my bolt guns, so I can swap out optics in just a couple of seconds. They make them in both the 30mm and the 1".....Brownell's and Midway both carry them.
     
  6. ilmonster

    ilmonster Member

    Joined:
    Feb 19, 2004
    Messages:
    551
    Location:
    Wisconsin
    A company named Spuhr makes one piece base/ring mounts - very nice ones.
     
  7. ilmonster

    ilmonster Member

    Joined:
    Feb 19, 2004
    Messages:
    551
    Location:
    Wisconsin
    Actually, these need to be mounted on an existing picatinny rail - not what you're looking for.
     
  8. jmr40

    jmr40 Member

    Joined:
    May 26, 2007
    Messages:
    10,212
    Location:
    Georgia
  9. NeuseRvrRat

    NeuseRvrRat Member

    Joined:
    Jan 24, 2011
    Messages:
    2,098
    Location:
    Wilmington, NC
    DNZ Products makes an excellent mount. they are rock solid.
     
  10. ThirtyOughtSix

    ThirtyOughtSix Member

    Joined:
    Jan 5, 2013
    Messages:
    25
    +1 for DMZ Gamereapers. They're all I use.
     
  11. jlewis406

    jlewis406 Member

    Joined:
    Jun 28, 2012
    Messages:
    37
    Location:
    New Mexico
    I think I am going to go with the DNZ mount. I do love GG&G. When I lived in Tucson I could just call them up and tell them what I needed and it would typically be built and ready by the end of the day or the next morning.
     
Thread Status:
Not open for further replies.

Share This Page