Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

Why isn't there more "progressive springs" used in guns?

Discussion in 'General Gun Discussions' started by twoblink, Oct 15, 2004.

Thread Status:
Not open for further replies.
  1. twoblink

    twoblink Member

    Joined:
    Dec 22, 2002
    Messages:
    3,736
    Location:
    Houston, Texas
    Like cars etc.. It seems like progressive springs are a good idea, and would work well in guns, so I'm wondering, why aren't progressive tension springs used more often in guns?
     
  2. Hawk

    Hawk Member

    Joined:
    Dec 24, 2002
    Messages:
    3,512
    Location:
    Grand Prairie, TX
    From Wolff Gunspring's FAQ:
    I'm no expert so couldn't address WHY keeping a slide closed as long as possible is a good thing with heavy loads...
     
  3. twoblink

    twoblink Member

    Joined:
    Dec 22, 2002
    Messages:
    3,736
    Location:
    Houston, Texas
    because work = F over Time, and so when you increase Time, and maintain the same F, then your work is decreased... Thus keeping it closed as long as possible, reduces the work done on the gun.. (or in laymen's terms, beating up of the parts)
     
  4. FNFiveSeven

    FNFiveSeven Member

    Joined:
    Jan 3, 2003
    Messages:
    538
    ?

    Work = Force * Dist which does not equal Force/Time.
     
  5. ShaiVong

    ShaiVong Member

    Joined:
    Dec 25, 2002
    Messages:
    1,106
    Location:
    Raccoon City, USA
    Work is Force over distance, power is work over time, right?
     
  6. Amish_Bill

    Amish_Bill Member

    Joined:
    Nov 29, 2003
    Messages:
    1,543
    Location:
    atl ga
    Try this -

    While the barrel is locked to the slide & frame, recoil energy is spread over the entire mass of the gun. When the barrel unlocks from the frame, only the barrel and slide are absorbing the recoil energy.

    heavy load into full mass = lower acceleration & overall velocity.
    heavy load into reduced mass = faster acceleration of the slide and a sharper thump when it hits full retraction.

    It's just a theory.
     
  7. Larry Ashcraft

    Larry Ashcraft Moderator Staff Member

    Joined:
    Dec 24, 2002
    Messages:
    11,628
    Location:
    Home of Heroes, Pueblo, CO, USA
    A couple of years ago, Richard Heinie had a bunch of progressive springs for sale "cheap" on the 1911Forum. I PMed him and told him I might be interested, then I asked my 'smith about getting them. He said he didn't like them, so I PM'ed Richard back and told him what my 'smith said. Here's what the man said:
     
  8. FNFiveSeven

    FNFiveSeven Member

    Joined:
    Jan 3, 2003
    Messages:
    538
    ShaiVong,

    Work (aka energy) is force times distance, the greater the distance with any given force, the more work done, lifting a 5 kg weight abover your head is 5x as much work as lifting a 1 kg weight above your head. Power is work over time, i.e. the rate at which work is being done.
     
  9. FNFiveSeven

    FNFiveSeven Member

    Joined:
    Jan 3, 2003
    Messages:
    538
    Amish Bill,

    The total recoil energy can only be changed by changing the mass of the gun (assuming the same load). A semi auto and a revolver of the same mass shooting the same load have the same recoil energy. However, the semi auto feels less because the time over which the energy is delivered to your hand is extended, causing the power to reduce. The spring slowly delivers the recoil energy to the frame (and then to your hand), whereas the revolver delivers any recoil instantaneously.

    I think progressive springs are a great idea in guns, and here's why. Let's say you're shooting you 1911 with a particular load, say a 185 grain low recoil handload. Because of the low recoil impulse, you need to use a light spring to allow the slide to move all the way back, if you use a heavier spring, the slide will short stroke on you and the gun jams. But now, let's say you shoot a +p 230 grain load with the same gun. Well now, that light recoil spring isn't enough as the slide comes flying back and batters the frame, wearing it out and giving you a light push followed by a sharp thump as the frame instantaneously dumps all of its energy into the slide (and you hand). With a progressive spring, you get the best of both worlds. The first part of the movement is light, so that you can shoot your light 185 grain loads without short stroking. But near the end of its travel, the spring stacks up to 20, 30, and 40 lbs so quickly that even when you switch to your +P 230's, the slide still doesn't smash into the frame, greatly extending the lifetime of your frame and greatly reducing the perceived recoil. Of course, the best way to minimize felt recoil is to use the one perfect spring for each load, but that's a pain in the neck and the progressive spring is an excellent compromise for a gun that needs to digest whatever it's given.
     
  10. JohnKSa

    JohnKSa Member

    Joined:
    Jan 1, 2003
    Messages:
    12,784
    Location:
    DFW Area
    Be very careful about using non-factory progressive recoil springs or lighter than normal recoil springs in Glocks.

    The slide is held forward in battery by the recoil spring, but there's also pressure to the rear from the striker spring. When the trigger is pulled, this applies rearward force to the striker which in turn pushes harder on the slide. With a light or progressive recoil spring (particularly with an 8lb or higher connector) it's possible to push the slide partly out of battery with trigger pressure. That's not such a good thing.
     
Thread Status:
Not open for further replies.

Share This Page