Search results for query: *

I wish to thank those who reponded to myquestions about 3-d printing of carbon,I did not get a definitive answer,but I was disabused of my belief that winchester made barrels of carbon. If anyone else has anything to add I would appreciate reading it.

I carbon comes in many forms,winchester made shotgun barrels out of one form.So it seems to me that a perfecly durable pistol might be built by printing,if that form of carbon can be printed. Also,if one is familiar with investment casting[jewelry] one could print a pistol in wax and cast it in...

Has anyone come up with a printed pistol frame? Is there there any research into graphene for firearms application?

My cz52 fails to feed quite often with 9mm.parabellum but is very good with Largo,so of course I go with that.I am surprised that with all the Stars,Llamas,&Astras out there, that there is not sufficient interest to make it a commecial proposition.

I am interested in the Obregon pistol,I checked US.patent<but it only covers the combination slide latch mag-catch-safety. Iwish to see the patent on the cam groove lockup.Can any one advise me on access to the mexican patent office,or if Sr.Obregon secured a seperate patent for that in the US.

Althoug I probably can't afford it It's nice to know Ican use 9*23mm. Thank you all for the info. To MACH1v shooter,I once had an astra400,in england,where I could only get sten ammo, when they came out with 2z ammo,I had to put a tapered reamer down the chamber because the high power caused...

I have a CZ52,Ibought a 9mm.parabellum barrel,which I reamed out to use my 9mm. largo ammo,which,unlike the parabellum,feeds very well. Question,although accuracy is fine,I wonder if the twist rate of the two 9mm'sis the same the para.barrel was purchased from the Makarov website,which no...

Back in 2002,Guns&Ammo did an article on a kit to convert a 1911 into a gas gun[like that H&K squeeze-cocker,also some time ago there was considerable fuss about a device to replace the grip-safety with asqeeze-cocker ,what happened?Inaddition they had sidebar of a husqvarna FFG, a gas...

HAVE ANY FIREARMS BEEN MADE USING 3-D PRINTING? And what about nicro-mesh technology?

7.62*25mm Than you Jonnyc, What I really want to know,is it pistol or subgun ammo/

Is the colt service ace,or the conversion kit still available ? considering the economy and the cost of centerfire ammo it should sell like hotcakes.

I have a box of ammo bearing chinese symbols,beneath the 7.62 is 50 & under that is70 any info.on this stuff would be appreciated.

mishmash2 I wish to install a yugo. tok.mag catch in my cz52,Ihave the catch assy.but do not know how deep to make the recess on the button side.None ofthe sites that Ihave found include this part even those dedicated to the disassembly...

Can anyone comeup with a dimensioned drawing of the hole forthemag catch in theJugoslav tokarev? The Makarov site had 9mm largo barrels for the cz52.

I asked if the 9*23mm winchester would work in the cz52 chambered in 9mm largo,but I can't find it anywhere. Also I thank those who answered my thread regarding the MAB15.

Does anyone still produce the mab 15?or does anyone sell them?

I have seen ads for new merwin-hulbert revolvers.Are there any out there? luger

9*23 winchester There used to be 9mm largo barrels for the cz 52,but now the ammo is non-existant,how would the 9*23 winchester work in a cz52? luger

To B&C C,thank you for your info.

Having acquired a yugoslav tokarev mag catch to instal in my cz52,I would appreciate someone telling me the width,in inches,of the yugoslav tokarev frame. Also,Iaccidentially happened on a site which showed the milling of a Sig p220 frame I would be delighted to find it again,any info would...