Search results for query: *

I'm in need of a crimp for my .44 loads and I'm not sure of what I should get these days there's quite a bit of a selection. I was just going to go with a lee FCD and be done but I'm just curious what's the input on that.

This trigger is out of my '68 Win 94 so I'm curious when they changed over to the "new" trigger (coil spring, etc).

So I got this beautiful (or so I thought) SKB 605 DU in 20ga for a great deal ($650) off gunbroker. Then today, I happily went to Dennis (my ffl) to pick it up.. And so I see this great looking shotgun sitting in its case as happy as it can be.. I fill out the 4473, he calls it in while I...

Why is this happening sometimes, and sometimes not? I tried playing with the final crimp and nothing ever turned up. Never had a problem with my 12's on a Grabber. Remington HV low brass 20ga w/ claybuster WAA20 rep. 14gr unique w/ 7/8oz.

I'm looking at a DU SKB for 500 at a shop, I looked online and they look to be going for about 1,200 on average. Based on that alone I should pick it up but I'm looking for more concrete opinions on this because I couldn't find much. I believe that it's skeet/skee in it right now. One...

I currently have a 1953 from Hungary and well, honestly it sucks, it shoots all over the place at 150 yards, I expect about a foot groups, not 5. Everything else is nice though but I'm getting rid of it –– Looking for a replacement, something more decent. Maybe a m39 if it's worth the while...

Has anybody used this --? Fires on the pull and release of the trigger correct?

I remember an article about redoing a crown on a barrel by getting an abrasive paste and chucking a screw in a lead roundball and coating the paste on the end of the bbl and going at it a bit at a time? I'd appreciate an idea where this article may be or a link to a similar article or...

Same weight bullet, same FPS range (about 2600). Silver bear shoots 2 feet high on the "1" setting, 100yrds Chezch/Hungarian is right on for the most part, same for the reloads.. Even though they are the same weight for the bullets and FPS are the same range, even when the reloads were...

Where can I find a BP measure to use with pyrodex or an alternative measure? I'm looking for about 70"gr" or so of RS.. In fact, if you could give me an # for the LEE powder scoops, that would be great. TC Hawken .50 w/ .490 ball and .018 patch.

Yea or Nay? It's in pretty good shape I'd say 87% only because of honest wear, barrel is marked 2 3/4. Full fixed choke. I do have the ability to reload 16ga so that is not a problem -- I'm just wondering if I should jump on this for 250?

Brown color for this powder? I put some in a pile and it burned immediately. Good or bad? Have about 2 pounds of this and would like to use it but if its junk. It's in a plastic jug, about 5 years old. It was closed and stored in a dark dry place?

I'm wondering if I could hose down my AR w/ non-chlorinated brake cleaner and wipe it down then hose it w/ more cleaner and blow it all off with a compressor and wash everything in CLP and brush it thru a few times then blow off the excesss CLP? Think of any harm done? I do this w/ my mosins...

I hear they rank below Arsenal and slightly above Vector but..? A local shop has one for 1k which is a bit more than what I want to pay but thats how things are today. Quality, accuracy, etc?

I can't find any data for the 54r w/ varget, there is none listed on hogdon's site.. So I'd appreciate it if someone had an idea where I could look. Thanks.

I have a ton of lead (literally) that I'm going to be using for casting for misc. bullets but thought I'd add slugs to the mix. I can reuse shotshells, wads (looking to use LEE drive key) Only thing I'd be buying (pretty much) is primers/powder but, I'm looking for experience in cost here...

HUGE PIC!

I'm trying to find some brass so I can reload for my Mosins, so I don't need to deal with the corrosive ammo and :barf: like that. I've found some on gunbroker but it's about $1 per.. No thanks!

I looked around but I could not really find out anything except they are earlier models that have been re-worked? Is there anything specifically special about them?

I picked up a Do-All Clay Hawk, it is the full cock model, think it was about 50 bucks. I can try it out and if I do not like it I can bring it back, but I fired off a couple of clays it looks pretty good but I will have to increase the tension in the spring.. I was thinking of the one step...