Quantcast
  1. This site uses cookies. By continuing to use this site, you are agreeing to our use of cookies. Learn More.

cleaning barrel

Discussion in 'General Gun Discussions' started by clin4580, Jan 25, 2004.

Thread Status:
Not open for further replies.
  1. clin4580

    clin4580 Member

    Joined:
    Sep 6, 2003
    Messages:
    42
    Location:
    Canton,NC
    Was just looking through my Sig manual and it states to never clean barrel from muzzle end.I have always cleaned all my barrels from the breach by pushing brush all the way through and then pulling back through.Should I not be pulling it back through muzzle end like a AR-15?
     
  2. HABU

    HABU Member

    Joined:
    Dec 24, 2002
    Messages:
    536
    Location:
    Western Washington
    While I am no expert, it seems that not cleaning the barrel from the muzzle end is SOP. I have heard that it is because the rod rubbing on the muzzle will wear the muzzle and affect accuracy. IF that is true, how does an aluminum rod wear a steel barrel? There must be more to this issue.
     
  3. CJ

    CJ Member

    Joined:
    Jun 20, 2003
    Messages:
    367
    Location:
    Southwest Colorado
    I could be wrong, but I believe the bigger issue is to avoid pushing any junk back into the action of the weapon. There's enough crud that already works its way in there without shoving more into it to gum up the works. By pushing or pulling from the breech toward the muzzle, any metal bits or gunk will ideally go out the muzzle.
     
  4. Kaxter

    Kaxter Member

    Joined:
    Feb 11, 2003
    Messages:
    188
    I was told this as well. I think they say this because if you dont get the brush right on center and then push it in it may rub one side of the front of the barrel. I guess after several times you do this it could wear down part of the front of the barrel and reduce accuracy? Thats just my guess, but I have been known to be WAY off:)
     
  5. sm

    sm member

    Joined:
    Dec 22, 2002
    Messages:
    28,389
    Location:
    Between black coffee, and shiftn' gears
    Breech to muzzle, recommended to protect crown from damage and pushing gunk back into action.

    Use a muzzle guard if have to go from muzzle ...or use a OTIS pull through system, especially for revolvers and lever actions where one cannot remove bbl, or gain access like on a bolt where a bolt guide is recommended.
     
  6. Preacherman

    Preacherman Member

    Joined:
    Dec 20, 2002
    Messages:
    13,309
    Location:
    Louisiana, USA
    If you can find some in your area, try Sweet's 7.62 copper fouling remover. Works like prunes through a duck!
     
  7. sm

    sm member

    Joined:
    Dec 22, 2002
    Messages:
    28,389
    Location:
    Between black coffee, and shiftn' gears
    ROFL

    I'm really afraid to ask how you know this. :D
     
  8. Binkus

    Binkus Member

    Joined:
    Jan 19, 2004
    Messages:
    49
    starting at the muzzelend can cause small (almost micrscopic) scratches to the crown wich can affect the accuracy. It wont cause enough damage to completly miss your target but if your into competiton shooting it could eventully cause a enough of a problem to be of concern. It also helps to keep deposits out of the action.
     
  9. duckfoot

    duckfoot member

    Joined:
    Dec 29, 2002
    Messages:
    558
    Location:
    behind you, NC
    "prunes through a duck!"

    I've never had a problem with this.

    I agree, the crown could be marred if the person cleaning dosen't know what the heck they are doing.
     
Thread Status:
Not open for further replies.

Share This Page