Non-AR SBR

[coach z]

I'd still really like to SBR a glock 17 and put it in a chassis with a butt stock and fore grip.

 

[Olympus]

I'd still really like to SBR a glock 17 and put it in a chassis with a butt stock and fore grip.

I was thinking the Glock 34 MOS with a red dot on the slide and one of those Mako Group stocks would be cool. Then I realized a 10mm would be even more cool.

 

[Sam1911]

What does 922r have to do with it?

A gun that is imported as a handgun does not have to comply with 922(r). However, you can't then make a rifle out of it -- even an NFA short-barreled rifle -- without making it 922(r) compliant.

 

[jmorris]

I was thinking the Glock 34 MOS with a red dot on the slide and one of those Mako Group stocks would be cool. Then I realized a 10mm would be even more cool.

The only stocked Glock I have ever shot was a full auto 34 and it wouldn't be as much fun with just 15 rounds.

 

[Ryanxia]

I'm thinking my next one will be my PPS-43C in 9mm. Original folding stock is pinned closed and it is sold as a pistol.

Another cool one would be a cheap Remington 870 cut right down or as someone mentioned the Zastava AK pistol.

 

[wally]

I'm thinking my next one will be my PPS-43C in 9mm. Original folding stock is pinned closed and it is sold as a pistol.

If expecting to do this, you better check very carefully before buying as all that I have seen have the folding stock welded -- I gave up on the idea after seeing where the welds are located.

 

[redbullitt]

That little vector 45 ACP would be very cool.

Consider and Encore/contender as well. THEN you can shoot whatever caliber you want and not have to be married to anything in particular.

A little rossie 92 would be sweet too. Not sure how short you would want to go though as SBR lengths there dramatically affect tube magazine capacity. Somewhere I saw a setup that slightly angled the tube mag to accommodate a suppressor, but I'm sure that was pricey lol.

Personally I like the ruger 77/357 for a SBR, say at about 10 inches or so. Subsonic stuff would be a hoot. The 44 would be sweet too, but I think it is tougher to find a suppressor that will handle that on a SBR without being too huge.

 

[zerobarrier]

A little rossie 92 would be sweet too. Not sure how short you would want to go though as SBR lengths there dramatically affect tube magazine capacity. Somewhere I saw a setup that slightly angled the tube mag to accommodate a suppressor, but I'm sure that was pricey lol.

Look at the pic I posted on the first page, it can only hold 6 rounds after being cut and threaded.

 

[Ryanxia]

If expecting to do this, you better check very carefully before buying as all that I have seen have the folding stock welded -- I gave up on the idea after seeing where the welds are located.

The older ones were welded, later on the switched to making the button oversized for the hole so it can't be depressed and adding a bar underneath. In any case shouldn't be a problem and it's something unique.

 

[redbullitt]

Not too bad on the rossi, but yeah definitely a consideration there. That is where the mag fed ruler 77/357 shines. Take that barrel as short as you like and the capacity stays the same, though less than the lever action in most cases still.

All that said, I would take a nice short lever with a suppressor any day lol.

 

[TIMC]

I'm currently working on an SBR made out of a Zavasta PAP M92 AK pistol in 7.62x39, when finished she should look something like this one.

 

[MasterSergeantA]

You could also take a Ruger PC-9 and cut it down. Takes the P-89 magazines, some of which are/were in capacities up to 50. Heavy gun, by carbine standards, but semi-auto and can be fun to shoot.

 

[HRnightmare]

Zastava M92's make awesome SBR's.

I took mine and mounted an ACE folding stock to it. It is an awesome and tiny gun. Quite a bit of noise and muzzle blast though. I am looking into a device to redirect it .

 

[Olympus]

I can close to getting a PAP, but I actually decided on a dedicated 9mm AR. The biggest push was cost to shoot. With 223 and 762 being around $0.23/round, my 9mm reloads were looking a lot nicer at $0.05/round. I can do more shooting this way and maybe even save up for a suppressor next.

I ordered a Black Creek Precision dedicated 9mm lower rather than using a standard size with a mag block. Hoping it arrives soon. I'll try to keep everyone updated.

 

[TRX]

PPS43, Suomi, Magal replica...

My Form 1 for the Magal came in over a year ago, but I'm still collecting bits for it.