Search results for query: *

I'm wanting a .22 LR bolt gun with a threaded barrel. I have a nice CZ 452 bull barrel varmint. Would it be wise or practical to have a gunsmith thread this rifle's barrel? Or should I just buy one already threaded from the manufacturer? It wouldn't necessarily have to be a CZ but a quality...

Hi all. My son, 18, recieved a very nice 870 Wing Master 12 guage when his grandpa passed. We went out to bust some clay pigeons for the first time with it the other day. When bringing up the gun to fire, the stock doesn't let you get your eye low enough to look down the vent rib. Is it called...

Hi guys, I picked up an Aimpoint 3000 red dot scope yesterday at a small town gun show for 50 bucks. Are these any good? I have a Colt AR flat top that I might put it on but I'm kind of confused about how to go about it. Wouldn't the front sight post be in the way? Is there some way to mount the...

Hi all, my buddy just picked up a CZ 527 with a Mannlicher sp? stock and Leupold VX II glass. I told him to get it because all the ones I've seen anywhere are good to shoot .223 as well as 5.56 X 45. Well, I ordered 1000 rounds of Lake City ammo from Ammoman to split with him before I saw the...

I have the opportunity to buy a Bushmaster Varminter with the 24 inch barrel, fired only a few times for 800.00. It is like new and comes with some accessories and soft case. The one at Bud's Guns says stainless. Are there other models of Varminter? What is ya'lls opinion of this rifle and is...

I've just built up a 10-22, barrel, stock, trigger group, extractor, nice scope, you know the works, and will sight it in this weekend. Could someone tell me why people recommend squaring the bolt face to a .0425 rim depth and also pinning the firing pin so it cannot raise up? How do these mods...

I will have a .920 Green Mountain barrel on a Hogue over molded stock. I plan to get the dednutz one piece scope base and am using a Redfield Revolution 3x9x40 scope. What will work best the low or the medium height mount. Which is more ideal, the scope center 1.5 inches above bore? Or a mount...

Hi guys, just ordered some stuff to build up my stainless Ruger and have a question. I'll be getting a Green Mountain fluted bull barrel with the Hogue synthetic stock, a DNZ Dednutz medium mount and a Redfield Revolution 3-9x40 scope, also a Hornet products trigger group and a Volquartzen...

Hi everyone. I bought this wasr 10 yesterday from a guy at work, no more than 100 rounds through it. Took it out today and failure to feed is a big problem with this thing. I'm using Wolf hollow points. This happens with all mags. The tip of the bullets are stopping against the very edge of the...

Hi everyone. I bought this wasr 10 yesterday from a guy at work, no more than 100 rounds through it. Took it out today and failure to feed is a big problem with this thing. I'm using Wolf hollow points. This happens with all mags. The tip of the bullets are stopping against the very edge of the...

I understand the velocity/twist rate formula to get bullet RPMs, but wouldn't there be some slip between bullet and rifling initially near the chamber? I just don's see how the rifling can grab the bullet and immediately start it to spin down the barrel. Does it catch up with the lands and...

Hi guys, and gals. I recieved this vice gizmo this morning as a gift called a Jaw Horse. Very sturdy, portable, 3 legged stability. I clamped a small piece of plywood in it and it made an awesome shooting bench. Re sighted in a couple of rimfires this afternoon and it was rock solid with my...

Was in a gun store a while back to pick up my new CZ 452 Varmint and noticed a cool gun in the counter case. It was a Ruger 10-22 action with a short barrel and a pistol grip, with a nice bi pod. What was that called? Didn't seem too practical but I can't get it off my mind. Haven't been back...

Hi all, I'm new to this site but I've been lurking the archives for years. Thanks in advance for any help. I have a Colt MTC 6700 that somehow got a 2 inch scratch down to bare metal on the barrel. What is a good way to patch or repair this? I guess you would call this a Parkerized finish...