milsurpguy
member
- Joined
- Feb 12, 2021
- Messages
- 549
Got a new toy. It's my plandemic osprey9 sealed and recoil boosted. Who'd da thunk the plandemic would still be going strong a slow tax stamp later? (13 or 14 months, my slowest of 6 form four silencers by far)
The gun is a Beretta 92fs.
To really test out this new fangled Nealon device silencer I dropped some 380 with 90gr bullet loads in 9x19 cases and it cycled. I was trying to make it malfunction, without the silencer it definitely would not cycle.
Usually I load 9mm pistol with medium speed 9mm powders like unique, AA7, HS6, I'm starting to load all my 115gr with faster general dynamics cbi which burns a lot like universal in a 9mm.
I usually don't load faster than cbi or HP38 in any pistol.
So completely opposite of how I normally load. I'll be loading a "powder puff load" and I kind of despise loads like these because an accidental double charge is possible and they tend to run dirty.
For my clandestine 9mm loads they need to:
1, be quiet enough to not wake the baby when eliminating coyotes or other preds around the hen house.
2, The osprey is sealed so the loads have to be clean burning, bullets jacketed, ect.
3 use fast powder, as they are usually quieter.
4, don't have to necessarily be able to cycle the gun without the osprey.
But fast burning normally doesn't equal clean burning. Another reason I don't like fast powder puff loads.
I do have a pound of Nitro100 NF, that's the fastest burning stuff I have by far, next to that it's probably HP38. A big gap there. Nitro 100 NF is supposed to burn pretty clean in 9mm and make decent plinker loads.
So I was thinking 115gr, subsonic.
Should be pretty quiet?
I'm very sure those "380 loads in a 9mm shells" 90gr rounds were subsonic and still cycled.
The brass I'll use will be Remington, or some other average capacity no thrills case as I have a few hundred of each of them. Primers will be cci, bullets will be Sierra 115gr HP.
I could use Sierra 90gr 380 bullets.
I don't want to use 124 or 125gr bullets as I save those for my hot 9mm carbine loads and 147gr bullets for normal P and +P pistol loads but I can use them.
Anyone use nitro100 NF for 9mm?
With or without a silencer?
Anyone have any pet loads for nitro100 NF in a 9?
My load manuals don't have any nitro100 NF loads listed. I could just treat it like reddot, titewad, clays, ect and work up a load.
The gun is a Beretta 92fs.
To really test out this new fangled Nealon device silencer I dropped some 380 with 90gr bullet loads in 9x19 cases and it cycled. I was trying to make it malfunction, without the silencer it definitely would not cycle.
Usually I load 9mm pistol with medium speed 9mm powders like unique, AA7, HS6, I'm starting to load all my 115gr with faster general dynamics cbi which burns a lot like universal in a 9mm.
I usually don't load faster than cbi or HP38 in any pistol.
So completely opposite of how I normally load. I'll be loading a "powder puff load" and I kind of despise loads like these because an accidental double charge is possible and they tend to run dirty.
For my clandestine 9mm loads they need to:
1, be quiet enough to not wake the baby when eliminating coyotes or other preds around the hen house.
2, The osprey is sealed so the loads have to be clean burning, bullets jacketed, ect.
3 use fast powder, as they are usually quieter.
4, don't have to necessarily be able to cycle the gun without the osprey.
But fast burning normally doesn't equal clean burning. Another reason I don't like fast powder puff loads.
I do have a pound of Nitro100 NF, that's the fastest burning stuff I have by far, next to that it's probably HP38. A big gap there. Nitro 100 NF is supposed to burn pretty clean in 9mm and make decent plinker loads.
So I was thinking 115gr, subsonic.
Should be pretty quiet?
I'm very sure those "380 loads in a 9mm shells" 90gr rounds were subsonic and still cycled.
The brass I'll use will be Remington, or some other average capacity no thrills case as I have a few hundred of each of them. Primers will be cci, bullets will be Sierra 115gr HP.
I could use Sierra 90gr 380 bullets.
I don't want to use 124 or 125gr bullets as I save those for my hot 9mm carbine loads and 147gr bullets for normal P and +P pistol loads but I can use them.
Anyone use nitro100 NF for 9mm?
With or without a silencer?
Anyone have any pet loads for nitro100 NF in a 9?
My load manuals don't have any nitro100 NF loads listed. I could just treat it like reddot, titewad, clays, ect and work up a load.